Earticle

Home

Issues

한국기계기술학회지 [Journal of the Korean Society of Mechanical Technology]

간행물 정보
  • 자료유형
    학술지
  • 발행기관
    한국기계기술학회 [Korean Society of Mechanical Technology]
  • ISSN
    1229-604X
  • EISSN
    2508-3805
  • 간기
    격월간
  • 수록기간
    1999~2018
  • 등재여부
    KCI 등재
  • 주제분류
    공학 > 기계공학
  • 십진분류
    KDC 550 DDC 621
제11권 제2호 (11건)
No

학술연구

1

스카라 로봇의 성능 평가에 의한 제 2 암의 최적 설계

이종신

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.1-8

※ 기관로그인 시 무료 이용이 가능합니다.

In this paper, optimal design of the second arm in a SCARA robot was studied. The mass and moment of inertia of the second arm of a SCARA robot have great effects on performance indices such as cycle times and torques of the first and second axes. To reduce the mass and moment of inertia, optimal design was carried out by FEM analysis using parameters such as width and height of the arm rib, which was newly adopted to decrease the arm thickness in keeping stiffness. Computer simulation was conducted in X and Y directional paths. As a result of the optimal design, maximum torques of the first and second axes decreased by 10.1% in maximum.

4,000원

2

디젤기관의 연소활성제 첨가에 따른 성능 및 배기특성에 대한 실험적 연구

김홍석, 강형수

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.9-13

※ 기관로그인 시 무료 이용이 가능합니다.

In this study, the potential possibility of oxygenates on butyl ether(below BE) was investigated as an combustion activator for a direct injection diesel engine. It tested to estimate change of engine performance and exhaust emission characteristics for the diesel fuel and oxygenates additives blended fuel which has four kinds of blended ratio. The smoke of blended fuel(diesel fuel 80vol-%+BE 20vol-%) was reduced in comparison with diesel fuel, that is, it was reduced approximately 26%. And, power, torque and brake specific fuel consumption(BSFC) didn't have no large differences. But, NOx of BE blended fuel was increased compared with diesel fuel.

4,000원

3

수치해석과 모형시험을 이용한 트롤어선의 선형개발

김현수

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.15-21

※ 기관로그인 시 무료 이용이 가능합니다.

To fulfill the design requirement from the Algeria owner, Hull form development of a trawl fishing boat was performed. Model test at CWC in INHA Technical collage was carried out to investigate the resistance characteristics and CFD analysis using FLUENT was performed to examine flow patterns and pressure distribution around hull etc. The designed hull form satisfies speed-power requirement of 10.5 knots at installed power. This paper describes the design feature of trawl fishing boat and evaluates the model test results and CFD results. The design constraints for Algeria trawl fishing boat were explained and the speed of the ship was compared with sea trial results.

4,000원

4

연성접착제를 사용한 접착이음의 강도평가에 대한 해석

박성완

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.23-32

※ 기관로그인 시 무료 이용이 가능합니다.

The objectives of the present study are to show how to predict the crack initiation at the terminus of adhesive bonded joints to calculate the crack growth in the adhesive layer using the total strain energy release rate. The crack propagation for ductile adhesives is theoretically estimated using -curve. -curve is determined from static shearing tests of single lap joints. The total strain energy release rate for single lap joints is evaluated using a boundary element analysis. The strength prediction is conducted by means of the R-curve and the total strain energy release rate.The conclusions are summarized as follows; (1) A crack propagation geometry of the bonded structure using ductile adhesive was predicted from the distribution of the total strain energy release rate. (2) The final failure load for lap joints is predicted by the R-curve method based on the fracture mechanics. (3) The final failure load for stiffened plates with a steel L-beam is predicted by the R-curve method based on the fracture mechanics.

4,000원

5

동력경운기용 고구마 수확기 개발

조기현, 정형길

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.33-37

※ 기관로그인 시 무료 이용이 가능합니다.

This study was carried out to investigate of the performance for Sweet potato Harvester using Power-tiller. There was highly reduction in energy consumption using by Sweet potato Harvester of Power-tiller. A diesel engine with four cycle with single cylinder, water cooling and rated output 8.1 kW/2200 rpm was selected. The experimental factors for performance test, engine speed ranged from 1000 rpm to 2400 rpm, and BSFC, efficiency, traction power, and vibration were measured. The results obtained were as follows; engine output were increased from 4.4 kW to 5.74 kW at 1800 rpm and increased to 8.83 kW at 2400 rpm The specific fuel consumption was decreased to 320 g/kW.h at engine speed 2200 rpm and the traction power were showed 420~440 kgf.

4,000원

6

시스템 히트펌프의 용량조절 및 최적화에 관한 연구

최종민

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.39-44

※ 기관로그인 시 무료 이용이 가능합니다.

A system heat pump provides the benefits of comfort, energy conservation and easy maintenance. Recently, the system heat pump has been employed in small and medium-sized buildings. However, the performance data and control algorithm for system heat pump are limited in literature due to complicated system parameters and operating conditions. In the present study, the performance of a system heat pump with two indoor unit is measured by varying indoor loads, EEV opening, and compressor speed. In addition, the integral optimum regulator which includes MIMO control algorithm is proposed. The capacity modulation and optimum capacity for each indoor unit can be adjusted by utilizing the EEVs opening and compressor speed. The proposed scheme shows appropriate control performance at test conditions.

4,000원

7

로봇암의 경량화를 위한 중공형 서보 조립체 개발 및 적용

고석조, 이영진

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.45-50

※ 기관로그인 시 무료 이용이 가능합니다.

Robotic manipulators are increasingly deployed in complex environments or to perform complex tasks. Studies on dual-arm-robots have been continually carried out in robotics areas to provide robots in dangerous environments, similar to those which human beings would be normally in, without a special change to the working environment. In previous study, a dual-arm-robot has been designed. The robot, however, has some defects in its heavy weight and big shape. In order to reduce weight of an arm robot, the robot has been designed using a hollow-shaft-servo- assembly. The hollow-shaft-servo-assembly is composed of a hollow-shaft-servo-motor, a hollow- shaft-harmonic-drive, a hollow-shaft-brake, a hollow-shaft-encoder, and a servo-drive.

4,000원

생산기술

8

히트펌프 시스템을 이용한 멸치 건조기 성능

장인성

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.51-58

※ 기관로그인 시 무료 이용이 가능합니다.

An experiment was carried out to evaluate the anchovy dryer performance using heat pump. We manufactured single stage refrigeration system using R22 and the dryer objects is frozen an anchovy. According to frame mobile method of the drying room inside divided at 3 drying rooms. After operating 13 hour machineries and accomplished a dryness experiment. The result which accomplishes an experiment, the dry condition which follows in frame movement of the drying room did not appear. According to the tray which is being put but in the frame the condition of anchovy dryness appeared different. It is concluded that the mean moisture evaporation rate is 60.7%, and the mean production of dryer an anchovy is 1.62 ton/day per dryer room.

4,000원

9

이동통신 옥내기지국용 에너지 절약형하이브리드 냉방기 개발

김영득, 이성제, 이주성, 나도백

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.59-65

※ 기관로그인 시 무료 이용이 가능합니다.

The hybrid cooling system of vapor compression system and naturally circulating coolin system using R-410a for indoor mobil tele-communication center(IMTC) is developed and its performance is experimentally studied. Its results are summarized as follows. First, cooling capacity of naturally circulating cooling system is proportional to indoor and outdoor temperature difference and it has max. 4,550 kcal/h at indoor and outdoor air temperature difference 15℃. Second, heat exchangers of evaporator and condenser should be designed and constructed to be able to get maximum refrigerant capacity by naturally circulating force and to enhance heat transfer by refrigerant. Third, cooling capacity of hybrid cooling system has optimum operating point according to refrigerant charging capacity and refrigerant charging capacity of naturally circulating cooling system is 30~50% more than vapor compression refrigeration system.

4,000원

10

흡입형 분무용 액체 충진기에 관한 연구

조명현, 김원배, 최병준

한국기계기술학회 한국기계기술학회지 제11권 제2호 2009.06 pp.67-73

※ 기관로그인 시 무료 이용이 가능합니다.

Sucking spray type liquid dispenser does to ply piston by exclusive use cylinder, did so that dispenser may can do pumping, and control sucking and interception of dispenser by sucking piston and interception node in main cylinder interior and control coating emperor's the spray amount more minutely in main cylinder, various coating emperors of low viscosity so that fixed quantity spray is possible spray type liquid dispenser be. In this paper, spray angle and theoretically cover extent in actuality cover extent is difference, spray form, spray air, spray high, over lap extent according to use usage becomes different and actuality cover extent applies over lap 20[%], and succeed to reduce error of cover extent maximum theoretically with actuality cover extent and got near result in cover extent of 10[%] withins.

4,000원

11

4,000원

 
페이지 저장