Earticle

This study deals with the improvement of production process on a flow production system with the consideration of six sigma. We analyze the production process and survey the important factors of improvement of productivity. Using a six sigma, we find strategic point and suggest a reformation of production process. We applied a simulation technique to simulate the production line proposed by the result of the Six sigma. With the result of the simulation, this study analyzes the propriety of production line and proposes the alternatives of new production process.

CC 프로세스는 부가 구성물들뿐만이 아니라 전체구조물을 자동화로 만드는 것을 목적으로 한다, 이런 목적을 위하여, 새로운 Trowel 메카니즘이 3D 자유형상을 만들기 위해서 기본적으로 필요하다. 이 논문은 선회하는 Side towel을 사용하여 3D 자유곡면의 제작에 대한 기초적인 조사 및 개념을 보여준다. 특히, ceramics 재료를 이용하여 실험과 개발과정, 및 장래의 적용범위가 상세히 설명된다.

Preliminary investigation of CC process indicates that the process is feasible and has significant potential in construction automation approach of large objects. The process aims at automated construction of whole houses as well as sub-components. The potential of CC became evident from the initial investigations and experiments with various materials and geometries. Using this process, a single house or a colony of houses, each with possibly a different design, may be automatically constructed in a single run as shown on . Experiments with ceramics material show the versatility of the process relative to the use of a variety of fabrication materials. In addition to the use in rapid fabrication of large components, the process also has its niche in rapidly fabricating certain components for aerospace and automotive industries, where minimization of green machining is warranted.

Because of not accepted on escape using elevators in fire emergency has some background. In the background elevator hoistway has turn into smoke spread route in fire. The escape that used an elevator was not able to make ends meet; of the big confusion is expected that cannot control the escape adequately, and do that elevator facilities breakdown possibility by the fire water, the escaper shut in car. Therefore ban on elevator service in fire time as a general rule. Recently, a few company promote super high-rise architecture in the country, a fire disaster prevention and human life safety measures preparation for PBD(A Performance Based Fire Protection Design) are studied concretely. And there is the escape example in fire time that used an elevator in the foreign country. You must promote it so that the escape measures that used enclosed stairway and an elevator in charge of a function of the mutual supplement. The result of this research can be used for establishing the standard and regulation for using elevators in fire emergency.

It compared subcontractor with contractor that are wages, the labor hour and labor condition of the work environment back are inferior relative. The subcontractor which basically the contract workers evade the dangerous process or the difficult work, the dirty work back what is called 3D the case which does to keep a business is many. so With life it will be threatened consequent health directly. The possibility where the subcontractor will be exposed to danger work came to be high. Together the reason of subcontract at managing the big business the case which becomes accomplished in objective, about lower the immediacy safety&health problem, subcontractor assigned workers is the actual condition only it could not be deteriorated more in public finance of the supply and enterprise and technical ability insufficiency. Consequently it prevents the subcontract which danger work is insensitive from this research and immediacy of the subcontract workers who is weak hygiene circumstance complement the plan it will be able to secure the immediacy safety&health subcontract workers, substantially to prepare in the hazard subcontract proprietor.

The purpose of this article is to examine the relationship between unsafe behavior, human factor and human error. For the object, several correlation analyses for those three elements were implemented. Several hypotheses for the relationship between them was suggested. The suggested hypotheses were verified by a comprehensive survey received from 132 safety manager of manufacturing industry. The conclusions were proven from the hypotheses verificaiton as belows; 1) The dependent relation items between unsafe behavior and human factor are dress protection tool, machine(equipment) and working rule have a dependent relation. 2) The dependent relation items between human factor and human error are uncommunication, control, slaps, fatigue, education, system, unmonitoring, failure. 3) The dependent relation items between human error and unsfafe behavior are decline and product/working method,failure and uncommunication have a dependent relation.

This paper suggest the methods when we solve problems by TRIZ before grasp of customer needs by Kano model. Recently, many companies are very interested in TRIZ such as Six Sigma. Especially, the company commences to use TRIZ for solving a lot of problems in which occur by products and services. But It will be happen a lot of time and costs to solve all problems completely. Finally, This paper helps more effective problem definition to avail Kano model for reducing time and costs at solving problems by TRIZ.

The purpose of this paper is to develop an efficient production strategy with changing factors to influence the productivity. The factors would be the number of Multi-Function worker, the method of job dispatching, and lot size. A simulation model has been developed for this study. We used AutoMod simulation and the process activity was animated to follow the flow of process easily. The alternatives have been tested through the simulation model, and the various alternatives is proposed for the efficient production strategy. We hope that the system is applied to similar types of small and medium-sized enterprises to develop an efficient production strategy and to achieve the satisfactory result.

ogistics creates a boom in accordance with the recent new technique's development along with the recent RFID/USN of ubiquitous computing technique. The wave of 4PL(Fourth Party Logistics) that added the strategic consulting based on new IT techniques to logistics outsourcing through existing 3PL service with is a great issue. Moreover, the customer enterprises which contained manufacturers and distributors need the one stop service, therefore a method for effectively dealing with global logistics' environment changes is needed. Above all, a development of the 4PL system with RFID is very urgent. We developed the RFID u-4PL system progressed more than the present system, in which we applied many international standards. Finally, we constructed the web service based on Web 2.0 because of important condition of 4PL.

본 연구는 최근 물류 활동 전반에 걸쳐 무선주파수를 이용해 상품과 사물에 내장된 정보를 읽어내는 기술인 RFID(Radio Frequency IDentification) 응용기술과 유비쿼터스 환경에서의 POS(POS : point of sales) 시스템의 발전 형태를 예측하여, 향후 국내 외 대형 할인점에서 적용할 수 있는 RFID 기반의 이동형 u-POS 시스템의 핵심기술개발에 관한 연구이다. 본 연구는 RFID 기반의 이동형 u-POS 시스템의 핵심기술을 크게 H/W와 S/W로 구분하여 H/W 측면으로는 기존의 쇼핑 Cart를 대체 할 수 있는 u-Cart 개발을 목표로 하고, S/W 측면으로는 기존의 POS 시스템과 연동 할 수 있는 u-Cart의 클라이언트 어플리케이션과 매장관리 서비스 모듈의 개발을 목표로 한 내용에 대하여 발표하고자 한다.

21세기 동북아지역 물류중심국가로 발돋움하기 위해서는 변화속도가 빠른 지금의 정보화시대에 잘 적응해야 하고, 다변화하는 소비자의 욕구에 충분히 만족할 수 있을만한 서비스를 제공해야 한다. 특히, 항공물류에 있어서 많은 수요가 있고 정확하고 빠른 서비스 기술의 개발이 요구되는 것을 파악하여, RFID를 이용한 개발 방안을 모색해 보고자 한다. 항공물류 서비스 전 프로세스에 RFID를 적용하고, 이것을 테스트하여 테스트 결과 분석을 하는 RFID 사업을 검토하여 현실 가능성과 추후 연구 과제를 제시하고, 항공 물류 서비스 기술 개발을 도모하고자 한다.

With the development of the Korean economy, the number of arson fire has been radically increased and become a huge problem and issue in Korea Society for last several decades. This study is to establish the fire life safety strategy regarding the arson fire through performing the computer simulation based on fire scenarios with researching domestic fire statistics and cutting edge techniques and methods for fire characteristics and fire dynamic. In addition, to design the fire life safety strategy depending on the arson fire pattern, the flow and characteristics of fire flames and smoke is analyzed by the computer modeling.

Nowadays obesity has been become a serious social issue. Many researches are trying to find the root cause of obesity. Obesity causes various kinds of disease and safety accidents in work places. Thus, the main objective of this study is to analyze obesity index of citizens in Seoul which is a metropolis of Korea and a densely populated district. In order to analyze a detailed somatotype of citizens, age groups are divided into 30-34 years, 35-39 years, 40-49 years, and 50-59 years according to gender respectively. The result of this study can be applied to the comfortable and appropriate design for workers.

The main objective of this study is to provide numerical guideline for size establishment of safety shoes about adult men(over 20 years) compared to physical standards of nation (report published in 1997). The sample for this work was chosen from data which were collected and measured by Size Korea during two years (20032004). In order to analyze and compare features of men's foot, analysis was performed about 1,685 subjects on 2 parts such as foot length and foot circumference. For the specific comparison on foot size, Mollison's comparison graph was used. The result of this study can be applied in manufacturing and design of shoes and socks. Also, it will enable us to have fruitful information on considerable items during manufacturing and design of safety shoes.

Ultimate goal of this research is to develop a web-based forecasting system of industrial accidents. As an initial step for the purpose of this study, this paper provides a comparative analysis of 4 kinds of algorithms including CHAID, CART, C4.5, and QUEST. In addition, this paper presents the logical process for development of a forecasting system. Decision tree algorithm is utilized to predict results using objective and quantified data as a typical technique of data mining. The sample for this work was chosen from 10,536 data related to manufacturing industries during three years(2002~2004) in korea.

Recently, all kind of 21C-typed electronic goods show the tendency of hightechnology and digital convergence rapidly. Also, failure mechanism which differs from original goods concept presents. Today, failure mechanism which differs from one that was happened by restricted harmful environment material before adapted the raw of environment material is changing the paradigm of reliability engineering. Thus, when applied the environment matter of original and secondary material at the electronic goods were removed, reliability assessment method and prediction stay into low level. This study suggests as solution to overcome these phenomenon. The study on the management method of environmental restriction substances which is recognized as important element in the reliability assessment about environment material of electronic goods and the study on reliability assessment method of PWB without environment material are progressed.

This paper deals with conformity assessments requirements for accreditation and certification bodies. This study also introduces conformity guidances of product certification and code of good practice. This paper presents general requirements for accreditation, recognition and registration bodies of environmental quality system and product certification.

This study introduces acceptance sampling plans and procedures for the inspection of bulk materials. This paper also presents statistical aspects of sampling bulk materials such as general principles and sampling of particulate materials.

This study introduces 2007 criteria of Malcom Baldridge National Quality Award (MBNQA) for performance excellence. Baldridge criteria is composed of the seven categories such as leadership, strategic planning, customer and market focus, measurement, analysis, and knowledge management, workforce focus, process management, and results. Moreover this paper proposes various integrated systems with MBNQA.

This paper presents geometrical product specifications of acceptance and verification tests for coordinate measuring machines(CMM). These specifications include vocabulary, measuring size, rotary table with fourth axis, scanning measuring mode, multiple-stylus probing systems, measuring, and, estimation of errors in computing Gaussian associated features.

This paper introduces radio frequency identification(RFID) information technologies for item management such as application interface of data protocol, data encoding rules and logical memory functions for data protocol, and, unique identification for RF tags. This study presents reference architecture and definition of parameters to be standardized, various parameters for air intreface communications, and, application requirements profiles.

In this paper, we summary known suggestion system which is useful a small and medium enterprise. We don't think suggestion system of a small and medium enterprise active. We reflect 2 points of suggestion system. We propose the Active Plan to Suggestion System for small and medium Enterprise which are (1) suggestion direction for enterprise future, (2) suggestion body for all employee included, (3) suggestion methods for all information shared.