Earticle

Purpose: This study was investigated the effect of multi-layer zirconia block type and design location on the mechanical properties of zirconia copings. Methods: Three kinds of multi-layered zirconia blocks (Snow princess multi layered block, Multi cherry, Dental zirconia pre-shaded blank) were used to identify the effects of the kinds of multi-layered zirconia blocks, design locations on mechanical characteristics of zirconia copings. 150 Zirconia copings were fabricated and fracture strength, hardness and microstructure were compared and evaluated. Results: Dental zirconia pre-shaded blank(2,256.9N) had the highest fracture strength of zirconia copings on all the design locations, and it was followed by Snow princess multi layered block(2,107.5N) and Multi cherry(917.0N). Snow princess multi layered block(1,949.7Hv) had the highest hardness of zirconia copings on all the design locations, and it was followed by Dental zirconia pre-shaded blank(1,671.7Hv) and Multi cherry(1,383.7Hv). The cervical layer had the highest fracture strength and hardness of zirconia copings in all the blocks, and it was followed by the cervical+gradation layer, the enamel layer, the enamel+gradation layer, and the gradation layer. Conclusion: It was found that the fracture strength and hardness were different according to the kinds of multilayer zirconia block and design location, and it was confirmed that it is lower than the fracture strength of white zirconia.

Purpose: This study was to investigate the effect of three different surface treatments on the shear bond strength of lithium disilicate ceramics to enamel. Methods: Totally 60 lithium disilicate ceramic disc specimens were fabricated with IPS e.max press (Ivoclar Vivadent, Schaan, Liechtenstein) and Mazic Claro (Vericom, Korea). 30 specimens in each lithium disilicate ceramic were assigned to 3 groups of the each following surface treatment: 1) 50㎛ airborne particle abrasion+silane, 2) 9.5% hydroflouric acid etching (HF)+silane, 3) 50㎛ airborne particle abrasion+9.5% HF+silane. Lithium disilicate ceramic surfaces after surface treatments were AFM examined. The shear bond strength was measured in a universal testing machine at 0.5mm/min crosshead speed. All data were analyzed using a two-way ANOVA and Tukey’s test(α=0.05). Results: The mean surface roughness of lithium disilicate ceramics ranged from 0.178㎛ to 0.441㎛. The mean shear bond strengths ranged from 23.81±2.78 MPa to 33.99±4.85 MPa. Conclusion: 1. Mazic Claro showed higher shear bond strength than IPS e.max press at 3 different surface treatments, and no statistically significant was observed. 2. The shear bond strength of IPS e.max press was strongly enhanced as surface treated with 50㎛ airborne particle abrasion and 9.5% hydroflouric acid etching. And there was no statistical significance at the shear bond strength of Mazic Claro with surface treatments.

Purpose: The purpose of this study was to compare two-dimensional fitness of the monolithic zirconia prosthesis by using different type of scanner. Methods: No. 26 abutment tooth of FDI system was selected for the study. Using the extraoral scanner and intraoral scanner, the abutment tooth was scanned 10 times and the scanned files were saved as STL files. CAD/CAM system was used to produce the monolithic zirconia prosthesis. marginal and internal gap of the monolithic zirconia prosthesis were measured by digital microscope(x160) and applied silicone replica technique was applied. t-test, a statistical software, was used to perform data analysis. Results: Marginal gap mean±SD of the monolithic zirconia prosthesis was 33±7.5㎛ with extra oral scanner and 34.7±11.1㎛ with intraoral scanner. axial gap mean was 40.5±3.5㎛ with extra oral scanner and 44.6±11.6㎛ with intraoral scanner. occlusal gap mean was 110.1±25.4㎛ with extra oral scanner and 64±9.7㎛ with intraoral scanner. Conclusion: In this study, fabricating zirconia prosthesis with different type of scanner was clinically applicable.

Purpose: This study was investigated the effect of multilayer zirconia block type and sintering method on fracture strength, micro structure and color of zirconia copings. Methods: Three kinds of multi-layered zirconia blocks were used to identify the effects of the kinds of multi-layered zirconia blocks and sintering methods on fracture strength and color reproducibility of zirconia copings. 60 Zirconia copings were fabricated and fracture strength, micro structure and color reproducibility were compared and evaluated. Results: In all the blocks, the CS group, which refers to the general sintering method had higher fracture strength of zirconia copings than the MS group that refers to the microwave sintering method(MCS/MMS; 2,107.5N/1,930.4N, DCS/DMS; 917.0N/879.1N, UCS/UMS; 2,256.9/2,050.7N). In relation to CIE L*, a*, b* values of zirconia copings depending on the kinds of multi-layered zirconia blocks and sintering methods, the MS group using the microwave sintering method had lower brightness and chroma than the CS group using the general sintering method. Conclusion: In all the blocks, the CS group(general sintering) had higher fracture strength of zirconia copings than the MS group(microwave sintering). In relation to CIE L*, a*, b* values of zirconia copings depending on the kinds of multi-layered zirconia blocks and sintering methods, the MS group using the microwave sintering method had lower brightness and chroma than the CS group using the general sintering method.

Purpose: The purpose of this study was to investigate the mechanical properties of polymer prosthetic and restorative materials for dental CAD/CAM using two test method; surface characteristics and shear bond strength. Methods: Commercialized CAD/CAM polymer blanks were investigated; One kinds of PMMA, and one PEKK blanks. A total of 20 PMMA and PEKK specimens were prepared, and each group was divided into 10 specimens. Average surface roughness was observed under surface profilometer. The contact angle was measured with a surface electrooptics. The bond strength was evaluated by a universal testing machine at a crosshead speed of 5mm/min. The data were statistically analyzed using independent t-test and Fisher’s exact test(P<0.05). Results: The PMMA and PEKK group showed a significant difference in the shear bond strength with the composite resin(P<0.05). The surface roughness of the PEKK group was higher than that of the PMMA group. The fracture mode were observed in PEKK groups with 50% showing adhesive remnant index score. Conclusion: PEEK is used as substructure material and composite veneering material is applied. PEKK resins will contribute to the development of successful products that will provide structural and aesthetic satisfaction.

Purpose: The purpose of this study is to evaluate the repeated measurement stability of scans related to dentition type. Methods: A normal model and the crowding and diastema models are also duplicated using duplicating silicon. After that, a plaster model is made using a plaster-type plaster on the duplicate mold, and each model is scanned 5 times by using an extraoral scanner. The gingival part and molar part were deleted from the 3D STL file data obtained through scanning. Using the 3D stl file obtained in this way, data is nested between model groups. Thereafter, RMS values obtained were compared and evaluated. The normality test of the data was performed for the statistical application of repeated measurements with dentition type, and the normality was satisfied. Therefore, the one-way ANOVA test, which is a parametric statistical method, was applied, and post-tests were processed by the Scheffe method. Results: The average size of each RMS in the Normal, Diastema, and Crowding groups was Normal> Crowding> Diastema. However, the standard deviation was in the order of Crowding> Normal> Diastema. The average value of each data is as follows. Diastema model was the smallest (5.51 ± 0.55 μm), followed by the crowding model (12.30 ± 2.50 μm). The normal model showed the maximum error (13.23 ± 1.06μm). Conclusion: There was a statistically significant difference in the repeatability of the scanning measurements according to the dentition type. Therefore, you should be more careful when scanning the normal intense or crowded dentition than scanning the interdental lining. However, this error value was within the range of applicable errors for all clinical cases.

Purpose: This experiment aims to provide the fundamental resources in developing a programme intended to prevent students from dropping out of their academics by promoting students to develop an optimistic psychological state, through analysis of the factors that influence students’ commitment to their major. Methods: A self-administered questionnaire was conducted from 19th of November of the year 2018, till 1st of December of the same year, with dental technology students located in W city as the subject. 261(93.2%) of the participants’ responses were used for the final analysis. Results: A negative association between factors of commitment to major and factors of academic dropout decision were portrayed to be of statistical significance (p<.01), and factors of commitment to major that influence dropping out of their academics were shown to be that of ‘autotelic experience’ (p<.001) with a negative ( - ) relationship, and ‘change in a sense of time’ (p<.01) with a positive ( + ) relationship of statistical significance, while the explanatory power of the model was shown to be 33.6%. Conclusion: In order to prevent dental technology students from dropping out of their academics, following their entrance, To achieve this, the department must consider the implementation of, aside from subject matters of the major, other various extra-curricular programmes, and programmes in which the supervisor is consistently providing consultations that are tailored to each individual student.

Purpose: The purpose of the study is to learn the importance of self-directed learning about career-preparation behavior of department of dental technology students. Methods: Using the questionnaire, the department of dental technology in Gyeongnam Province conducted a survey of students of department of dental technology at A and B college for one month from May 15, 2019 through June 15, 2019, and finally 204 students were surveyed for Self-esteem, Self-determination, Self-efficacy, Internal control, College life adaptation, Self-directed learning, and Career-preparation behavior. Results: Self-esteem among students has been shown to improve self-directed learning by increasing the stress of college life, and self-efficacy has only a direct effect on self-directed learning. In addition, self-determination and internal control of department of dental technology students were found to be variables that have a common positive effect on college life adaptation and self-directed learning. In addition, college life adaptation gives direct positive effect to self-directed learning, but indirect effect through self-directed learning was found to be stronger than direct effect on career-preparation behavior, and the career-preparation behavior of students was further strengthened through self-directed learning. Conclusion: The changes in college restructuring and various policies also suggest that students should actively seek ways to instill certainty about their major's vision and career path within the college rather than deciding their future through extreme measures such as academic secession at a time when anxiety and uncertainty about their career is strong.