Earticle

The surface microstructural changes, mechanical properties and corrosion resistance of Ti-Pd alloys for dental biomaterials have been investigated. Ti, Ti-Pd alloys were melted in arc furnace and the corrosion resistance of Ti-Pd alloys was evaluated by anodic polarization test. The surface microstructural changes and mechanical properties of Ti-Pd alloys were analysed by scanning electron microscope and Vickers micro-hardness tester. The vickers hardnees of pure Ti improved by addition of Pd but Ti-25Pd alloy showed decreasing compared with Ti-15Pd. And anodic polarization and potentiostatic test were conducted in 5% HCl to quantify the resistance to corrosion with the addition of Pd, There was no significant difference in corrosion resistance between pure Ti, Ti-5Pd and Ti-15Pd alloy. However, Ti-25Pd alloy showed decreasing compared with pure Ti in corrosion resistance. From these results, it was concluded that newly formulated Ti-15Pd experimental alloy have adequate hardness and high corrosion resistance, and this alloy is promising candidate for a successful dental casting alloy.

The purpose of this study was to observe the thermal expansion of the inlay waxes at temperature. Inlay pattern wax shows not only a high coefficient of expansion but also a tendency to warp or distort when allowed to stand unrestrained. The thermal expansion of inlay waxes was tested according to the treatment conditions for 10 minutes at 40'C. The thermal expansion of inlay waxes at various temperatures was measured with an electro dial gauge. The results were as fellows: 1. It is shown that the rate of thermal expansion of wax A is 0.2%, wax B is 0.29%, wax C is 0.38%, and wax D is 0.22% at 40'C. 2. It is shown that the coefficient of thermal expansion of wax A is 106*10-6/'C , wax B is , wax C is 152*10-6/'C , and wax D is s116*10-6/'C at 40'C. 3. The thermal expansion of the inlay waxes at 40'C was shown to increase in the order of wax C, B, D, A.

The purpose of this study is to evaluate possibility of using indirect composite resin instead of porcelain through the measurement of shear bond strength between zirconia core and indirect composite resin under treatment of RocatecTM system for improving the adhesion of indirect composite resin. 20 cylindrical zirconia core specimens were divided into 2 groups, according to zirconia surface treatment and attached materials: 1) treated with sandblast and attached with indirect composite resin, 2) treated with sandblast + RocatecTM system and attached with indirect composite resin. The shear bond strength of each experimental group was measured by MTS and the changes of zirconia core surface according to surface treatments were obtained by SEM observation and measurements of surface roughness. The mean shear bond strength values are 0.55+- 0.11MPa (Group SC) and 1.16+- 0.46MPa (Group SRC). The mean Ra values for the surface treatments were follows: 0.39+- 0.13(100ßum sandblast) and 0.50+- 0.03(100ßum sandblast + RocatecTM system). In the analysis of EDS, Si element was detected in the Group SC. The shear bond strength between zirconia core and indirect composite resin was improved significantly by using RocatecTM system.

A variety of the porcelain fused to gold(PFG) have been developed to which porcelain can be fused. PFG alloys developed for this purposed have a high melting point and do not discolor when combined with porcelain. The design of the compositions of PFG is very important to esthetic restorative materials applying to porcelain. The purpose of this study is on the change of physical and mechanical characteristics in PFG 18K alloy by the small additional elements. Principal results are as follows. The high Au alloy containing 18Karat gold contents is respectively Au(75%), Pd(10%), Pt(4%), Ag(4%), In(2%), Sn(2%), Cu(2%), Ti(1%). These alloys are composed mainly of gold, platinum, silver and palladium with a few percent of the additional elements. By the addition of small amounts of elements such as In, Sn, Ti, the fine grain castings are produced in gold alloy and the small addition of platinum is very effective in increasing of hardness and strength. These gold alloys are representative of the changes to be expected as a result of heat treatment. These changes in strength and hardness values are sufficient to demonstrate a significant difference in performance between a as-casted and a heat-treated. These alloys have mechanical properties characteristics of Type and Type gold alloys. These alloys are useful to porcelain-metal restorations and dental laboratory. Also the porcelain fused to metal(PFM) alloys containing gold are commonly use for dental purposes in dental laboratory.

Titanium and its alloys are widely used as dental implants materials because of their excellent mechanical properties. However, the alumina and zirconia ceramics are preferred to use as the substitute of Ti implants because there is a problems in esthetics and biocompatibility in Ti implant. The the glass infiltrated alumina ceramics are studied to increase the toughness and biocompatibility. The 45S5 and soda-lime glass powder was mixed with ethanol at ratio of 1:1 and brushed on the surface of alumina. Then it was heat treated in the electric furnace 1400'C at from 30 min. to 5 hours. The glass powder was controlled from 200 to 350um using ball milling. After heat treatment, the glass infiltrated specimen was tested in universal testing machine to measure the bending strength. The surface microstructure of each specimen was observed with SEM. The biocompatibility of 45S5 and soda-lime glass coated alumina was investigated using PBS at 36.5'C incubator. The specimen was immersed in PBS for 3, 5, 7, 10 days. After that, the surface morphology was investigated with SEM. As the results of experiment, the 45S5 bioglass infiltrated alumina show the increase of bending strength according to the increasing of heat treatment time from 30 min. to 5 hours at 1400'C Finally the 1370N bending strength of alumina increased to 1958N at 5 hours heat treatment, which shows 1.4 times higher. In contrast to this, the soda lime glass infiltrated alumina ceramics shows the convex curve according to heat treatment time. Thus it shows maximum bending strength of 1820N at 1 hour heat treatment of 1400'C It gives 1.3 times higher. However, the bending strength of soda lime glass infiltrated alumina is decreasing with increasing heat treatment time after 1 hour. The precipitation on the surface of 45S5 glass infiltrated alumina was revealed as a sodium phosphate (Na6P6O24H2O) and the amount of precipitation is increasing with increasing of immersion time in PBS. In contrast to this, there is no precipitation are observed on the surface of soda lime glass infiltrated alumina. This implies that 45S5 glass infiltrated alumina brings more biocompatible when it is implanted in human body.

This is a research for thickness change of denture base according to the shape of sprue & investment position of denture base in flask when injecting polyamid base resin for flexible partial denture as a part of study for Valplast among the flexible partial denture with a nylon base. It has been introduced several kinds of flexible partial denture product with a nylon base, but Valplast is the most widely used product among them. Valplast has been the most generally used material today since developed in 1950s in the United States as a material for flexible partial denture. Valplast is much more aesthetic than general metal-acrylic partial denture due to its translucent pink color and biocompatibility in terms of material characteristic. It keeps its flexibility for a long time after production, imposes a less burden on the teeth used as abutment, and it can be easily insert and remove due to its particular suppleness. Moreover, it is felt like real teeth more than metal-acrylic partial denture when being put in and takes alveolar bone under good protection since it receives occlusal force equally under the denture base. The most outstanding feature of Valplast is flexibility. The extent of its flexibility is determined by width & thickness of denture base. Considering general working procedure of Valplast, it can be seen that the thickness of denture base formed out of wax is increasing by the pressure while injecting resin. This research is to decide and test on the thickness increasing of Valplast by injecting pressure and the hypothesis upon that and is to prepare the basis estimating the increasing extent of thickness of denture base on the basis of the test result. In this test, it is expected occlusal malposition & thickness increasing of denture base by injecting pressure according to 4 kinds of test data which are to select 3 types of sprue method settling the forefront position at which the test material of fixed standard can be invested and to position the test material at the rearmost part keeping the minimum distance to set sprue. For 4 kinds of injecting test by investment position & sprue type, 20 test materials, 5 for each test were produced and a pressure of 1,180Kg was given with automatic injector of air cylinder type. The results are as follows: 1. For the amount of thickness increasing of denture base by investment position, the thickness of front investment is less increasing than the one of rear investment. 2. For the amount of thickness increasing of denture base by sprue type, the thickness of straight decompression sprue type which can absorb the injecting pressure after injecting polyamide base resin is less increasing than the other sprue types.

Statement of problem: Conventional techniques for implant framework fabrication produce significant error that is inconsistent with passive-fit requirement for osseointegrated implants. One of the etiologic factors which cause the errors is a sprue which may deform the framework during solidification and contraction. Purpose: This study was aimed to evaluate objectively effect of the sprue design on the accuracy of fit of implant prosthesis. Materials and method: Three different designs were considered relative to effect of casting accuracy. The first design had straight sprues and a button of excess alloy at the non-casting end of the sprues. The second was runner bar design(with the button). The last was straight sprues design(without the button). Gold cylinder and laboratory analogue had been used to diminish variables affecting to casting accuracy. Gold alloy and pressure-vacuum casting machine had been used. Marginal gap had been measured by SEM. One-way ANOVA and Duncan test had been used for statistical analysis. Results: The first design showed 79.87+-13.95um marginal gap. The second and third were 40.17+-15.8um and 35.17+-9.95um respectively. Conclusion: Straight sprues without button and runner bar designs were more accurate than straight sprues with button design(P<.05).

Recently, zirconia is widely used in the field of dental ceramics thanks to the proliferation of CAD/CAM systems. Accordingly, different types of zirconia block are being solid in the market. However, there are no precise, objective standards for properties of zirconia. This study concerns the flexural strength of zirconia ceramic for CAD/CAM block. The test specimens used for this study were ZirBlank(Acucera), ZirBlank shade(Acucera), VITA, Cercon(Densply) and Cerasys. The test results suggest that ZirBlank shade block shows the highest flexural strength and density among the zirconia blocks tested. Its flexural strength was 971 58 and its density was 99.89%. On the other hand, Cerasys block shows the lowest flexural strength of 576 36 and the lowest density of 94.85%. Given all, the density of the specimens is found to be directly proportional to strength and inversely to grain size.

Acrylic resin has been widely used for dental care since it requires relatively simple equipment for treatment and less time and cost are needed to make it and, furthermore, proper strength, dimensional stability as well as durability are ensured after treatment. A survey of denture users showed, however, that more than 60% of dentures installed need repair each year, 22~30% of which are due to falling out of teeth. This study is aimed at exploring the means to increase bonding strength of denture by reducing the causes for falling out of teeth during the processing of dentures. For this aim, the bonding strength of dentures was compares and analyzed before and after the glazed surface of teeth contacting denture was eliminated. From the analysis, it was revealed that there was a differnce of 4.3MPa in average in bonding strength between 20MPa for the glazed surface not eliminated and 24.3 MPa for the glazed surface eliminated.

The purpose of this study was to investigate the effect retention element formed by metal surface treatment method on the bond strength of indirect composite resin and metal. The metal specimens were cast from Ni-Cr alloy(Rexillium III). They were divided into 5 groups by applied retention element: 50um aluminium oxide sandblasting group, 250um aluminium oxide sandblasting group, 0.2 retention crystal group, 10% H2SO4 solution etching group, 110um RocatecTM Plus system group. Total 50 metal specimens were veneered with Sinfony indirect composite resin system. Specimens were tested for shear bond strength on an Instron universal testing machine and fracture mode of fractured specimens were analyzed by SEM and EDS. 1. 0.2mm retention crystals were most effective in improving the resin-metal shear bond strength (p<0.05). 2. Sandblasting by 250um aluminium oxide were more effective than sandblasting by 50um aluminium oxide in improving the resin-metal shear bond strength(p<0.05). 3. Fracture mode of resin-metal fractured surface were cohesive failure mode in 0.2mm retention crystal, mixed failure mode in sandblasted specimens, etched specimens and the specimens sandblasted with 110um RocatecTM Plus system.

Purpose: In this study, we tried to compare marginal accuracy when produce ceramic crown using all ceramic materials and existent metal-ceramic system. Material and methods: All-ceramic systems were E-max (Ivoclar/Vivadent, Lichtenstein), Lava(3M, U.S.A.) and Wol-ceram(Teamziereis, Germany). Metal-ceramic system(PFG) was composed of Au-Pt alloy (Metalor, Switzerlandand) and overlying ceramic(D-sign, Ivoclar/Vivadent, Lichtenstein). We fabricated metal master die with upper diameter of 7.95mm, bottom diameter of 9.00mm, height of 5.00mm, and taper of 6'. All ceramic system used 0.5mm thickness ceramic coping, while metalceramic system used 0.3 thickness metal coping. By adding dentin and enamel ceramics on each coping, a crown with a proximal thickness of 1.0 mm and occlusal thickness of 2.0mm was fabricated. Pressure of 2kg was applied for 10 seconds on each crown with static load compressor. Before and after cementation, we measured the marginal gap at 4 points of each crown using optical microscope. The data was analyzed using a Student's t test and repeated-measures of analyses of variance(ANOVA) followed by a Bonferroni test. A p value<0.05 was considered significant. Results: As experiment results, marginal accuracy of wol-ceram and Lava is no good when compared with marginal accuracy of PFG. But marginal accuracy of E.max is good when compared with PFG. This result showed not significant. The marginal accuracy of E.max is good when compared with marginal accuracy of wol-ceram and Lava. Conclusion: The marginal accuracy of E.max is very good when compared with marginal accuracy of another group.

This research is designed for a consumer, not a supplier when it was designed. And the purpose is to present the reference data which is in order to improve the curriculum by analyzing the present subject of the curriculum. The research collected the curriculum for Dental Technology from a total of 20 schools --3-year colleges and 4-year colleges-- all in Korea. And we analyzed the average credits of subjects from students. As a result of this analysis, we get the conclusion below: 1. In a distribution which students answered about each subjects; Dental esthetic, Dental morphology I II, Dental morphology practice I II, and Seminar don't have many credits and mostly have a converged tendency in high points, according to the arithmetic mean of the major basis subjects. 2. In an analysis of the correlation which is based on the distinction of sex; Dental ceramics practice III, Medical terminology, Seminar, and The major basis subjects have a meaningful difference. ( p< 0.05) 3. In an analysis of the correlation which is based on an age; The major basis subjects, and the application subjects have meaningful difference. ( p< 0.05) 4. In a correlation coefficient between subjects; The correlation coefficient of the major application subjects is higher than the major basis subjects. According to the student ? t, we found that the level of significance is p< 0.001, which is meaningful. We feel that Department of Dental Technology also highly need to design, and conduct focusing on a consumer who is working at the society, not a supplier. And we need to increase or decrease credits which have a meaningful difference.

This study explored the status of free time activities among the dental technicians who are working at Seoul, Gyonggido, and Gangwondo. On the basis of this research, we aim to present needs and applicable solutions to improve the working conditions and enhance the quality of life through more effective time management in free time activities that lead to their self development and far more enriched life. 500 subjects were randomly chosen and the questionary sheets were provided. Among them, 305 sheets were returned to be analysed through SPSS Win 10.0 software and the results are as follows; First, mean in the satisfaction of leisure activities was 3.44(SD=.73). Mean in sub categories was as follows; psychological factor(M=3.65, SD=.71), social factor(M=3.54, SD=.75), rest factors(M=3.52, SD=.63), physical factor(M=3.43, SD=.88), other factors(M=3.40, SD=.66), circumstantial factor(M=3.33, SD=.63), educational factor(M=3.24, SD=.73). Second, the most relevant sub categories in the satisfaction of leisure activities were social, educational, physical, and other circumstantial factors by sequence. Factors that affect leisure activities satisfaction were career and status of health, which shows statistical significance(p<.001). That is to say, contention of this study is that the general characteristics are closely related with and affect the types and the level of satisfaction in leisure activities of the subjects. Considering these results, the dental businesses and the associations of dental technicians should recognize the needs to improve the time management through more efficient cooperations between dentists and back office dental team, systemized working time, and introduction of incentive system among others. On the basis of this appreciation, the dental business should provide more time and various opportunities with the dental technicians. Dental technicians also need to reconsider their appreciations of leisure activities, that is, leisure activities are not just spending time doing something but they refresh them and enable them to be more active and faithful to home and work.

The purpose of this study was to evaluate the role of socioeconomic factors and health behaviors on the prevalence of oral diseases(dental caries and periodontal disease) among Korean adults. Data from the 2005 National Health and Nutrition Examination Survey was analyzed for adults aged over 19 years (n=25,215). Oral disease was defined as disease diagnosed by a dentist for the previous 12 months. Chi-square test and logistic regression analysis were used to conduct statistical analysis. The population without dental caries and periodontal diseases were used as the reference category for all analysis. The overall prevalence of annual dentist-diagnosed dental caries and periodontal diseases were 23.5% and 10.6% respectively. The relative risk of developing dental caries for graduates of middle school and lower were 1.53 times (95% CI: 1.24-1.89) more likely to develop dental caries comparing to college graduates. Low income earners were 1.23 times(95% CI: 1.01-1.49) more likely to develop dental caries than high income earners. Persons covered by national medical insurance were 1.45 times(95% CI: 1.08-1.95) more likely to develop dental caries comparing to persons covered by employee medical insurance. Compared with persons not eating snacks, the risk of developing caries in persons eating snacks once a day was 1.16(95% CI: 1.01-1.32), while those who snacked twice or more a day were 1.19(95% CI: 1.01-1.41). The relative risk of developing periodontal disease was 3.71(95% CI: 2.38-5.80) higher in older individuals than younger. In terms of education level, middle school graduates and lower were 1.54 times more likely to develop periodontal disease than college graduates. Low income earners were 1.47 times more likely to develop periodontal diseases than high income earners. Using data from a large, nationally representative sample of Korean populations, we support the hypothesis that the prevalence of oral diseases is related with socioeconomic factors and health behaviors. More intensive intervention efforts to reduce the prevalence of dental diseases are warranted in Korea.

The results are as following. This study aimed to furnish basic data for improving the oral health of the elderly by conducting research into the relationship between denture satisfaction and the perceived oral health status of elderly people with removable dentures. The study performed research involving 246 elderly people who were living in Jeonju and Iksan, jeonbuk, and who were 65 years old or over from August 1 to December 5, 2007. The research method was a face-to-face interview. 1. The denture satisfaction of respondents for the research averaged 3.74+-0.69, and there was a significant difference in their satisfaction according to the level of education, the cohabitant family type, the procurement of living expenses, the performance of leisure activity, the period of current denture use, the number of denture changes, the experience during a dentist visit for denture maintenance, the experience of restricted activity due to annual oral diseases, and the opinions about denture prices. 2. 48.8% of respondents answered that their oral health status was good, and there was a significant difference in their satisfaction according to the procurement of living expenses, the total period of denture use, the period of current denture use, the number of denture changes, the experience of restricted activity due to annual oral diseases, and the opinions about denture prices. 3. The most highly influential variable affecting denture satisfaction was the opinions about denture prices(R=33.7%). 4. The most highly influential variable affecting the perceived oral health status was the educational level(R=17.3%). 5. As a result of analyzing the relationship between denture satisfaction and perceived oral health status, more respondents were satisfied with their dentures the more they thought their oral health status was in good shape.