Earticle

Diesel engine has the advantages of strong power, low fuel consumption and good durability, so it has been widely used in transportation, automobile, ship and other fields. However, the nitrogen oxides(NOx) and particulate matter(PM) emitted by diesel engines have become one of the main causes of air pollution. Especially during idling, the engine temperature is low, and there are more residual exhaust gases in the combustion chamber, resulting in the formation of more harmful emissions. In this study, performance of a single cylinder, four-stroke, direct injection (DI) diesel engine fueled with diesel–biodiesel mixtures has been experimentally investigated.

In this study, we investigated the effects of EGR rate and engine load on the emission characteristics in a 4-cylinder common rail direct injection diesel engine fueled with canola oil biodiesel (BD) blended fuel. The biodiesel blend fuel, BD20 (20 vol.% biodiesel and 80 vol.% ULSD blend) was used at an engine speed of 1,500rpm. The experimental results showed that with the increasing of EGR rate, the combustion pressure and rate of heat release (ROHR) of three test fuels were decreased, and the ignition delay was extended, the carbon monoxide (CO) and particulate matter (PM) emissions increased slightly, but the nitrogen oxide (NOx) emission decreased clearly. On the other hand, with the increasing of engine load, the combustion pressure and ROHR were increased, and the CO and PM emissions decreased. However, the NOx emission was increased due to the rise of the combustion temperature.

In this study, we investigated the effects of EGR rate and engine load on the emission characteristics in a 4-cylinder common rail direct injection diesel engine fueled with canola oil biodiesel (BD) blended fuel. The biodiesel blend fuel BD20 (20 vol.% biodiesel and 80 vol.% ULSD blend) was used at an engine speed of 1,500rpm. The experimental results showed that with the increasing of EGR rate, the combustion pressure and rate of heat release (ROHR) of three test fuels decreased, and the ignition delay was extended, the carbon monoxide (CO) and particulate matter (PM) emissions increased slightly, but the nitrogen oxide (NOX) emission decreased clearly. On the other hand, with the increasing of engine load, the combustion pressure and ROHR increased, and the CO and PM emissions decreased. However, the NOX emission increased slightly due to the rise of the combustion temperature.

When an engine connecting rod is designed, it’s important to consider the buckling strength as well as deformation and durability of the rod. The buckling strength of a rod is mainly affected by the shape and area of shank cross-section and boundary conditions of its small and big ends. Buckling analysis by finite element method was carried out to evaluate the elastic buckling strength of a connecting rod that has non-uniform cross section areas. And the Merchant-Rankine formula was applied to predict the inelastic critical buckling load by considering the plastic buckling strength. Finally, the maximum allowable compressive load, which has 56.57kN, was predicted by considering the 1.7 buckling safety factor. It represents an approximately 40% greater than the maximum firing pressure.

The purpose of this study is to verify the effects of a port throttling and 1/4 diagonal port masking of an intake port of an SI engine. The fuel consumption rate increased with port throttling and masking under all operating conditions. However, the rapid combustion effect was increased in all operating conditions. It is consider that this is more influential on the suction resistance than the combustion efficiency increase through intake control. In addition, the increase in the burning velocity indicates that the flame propagation speed is increased by increasing the swirl moment during combustion.

The main reasons of diesel engine load under speed can be summed up as valve spring fracture, nozzle coking blocked hole, engine oil pipe fracture, fuel injection delay, fuel injection pump drive roll key. There are six symptoms. Using the symptoms and the reasons establishes fuzzy corresponding relation, establishing the automatic fault diagnosis fuzzy model of diesel engine load under speed, through the symptoms of diesel engine load under speed to judge its fault reasons, which could treat the faults quickly so as to ensure the normal operation of the diesel engine.

The load characteristics of engine main bearing are very important in the design of crankshaft and engine block. The stiffness of crankshaft and block, or the optimal dimension of the bearing can be determined according to the load level. This paper presents the load characteristics of engine main bearing. Two components of the main bearing load are measured during engine firing and motoring. The vertical and horizontal load components are measured by using the dynamic load cell mounted in each main bearing cap bolt. The measured main bearing loads are compared with calculated results by using the statically determinate method. The theoretical results, provided in this study, agreed well with the experimental results. The presented results are very useful for achieving optimal design of engine.

Cycle-to-cycle variation has long been recognized as limiting the range of operating conditions of spark ignition engines, in particular, under lean and highly diluted operation conditions. At a part load, some of the cycles tend to knock, while others may have incomplete combustion by the time the exhaust valve opens. An experimental study has been performed in order to evaluate the relative contribution of several relevant parameters on the cyclic variability in spark ignition engines. In general, the stability of engine operation is improved with fuel injector according to the optimal injection timing, but the stability of engine operation at idle is not improved compared with a practical gasoline engine. In this study, we investigated the relationship of the effect of operating conditions for the stability at low speed and load.

This work has investigated the exhaust emissions such as Total Hydrocarbon (THC), Nitrogen Oxides(NOx), and Particulate Matter (PM) characteristics emitted from the tail-pipe of a continuously variable valve timing (CVVT) gasoline-fueled engine with different intake valve opening timings and injection pressures at the part load condition. Valve overlap period was varied from $40^{\circ}CA$ to $10^{\circ}CA$ and fuel injection pressure was increased from 3.5 bar to 5.0 bar. THC and NOx emissions decreased as intake valve opening timing was advanced regardless of fuel injection pressure. When the fuel was injected with the condition of 5.0 bar at all of valve overlap ranges, THC levels were reduced by 55%. NOx concentrations were diminished about 75% as valve overlap increased. PM size distributions were analyzed as bi-modal type of the nucleation and accumulation mode. Comparing with fuel injection pressures, PM emission levels were decreased at high pressure injection of 5.0 bar condition.

The customers demand of a good vehicle agility consists of a quick reaction of the vehicle with the actuation of the throttle pedal on one hand and a high comfort level of vibration and noise within the vehicle on the other hand, which means the reduction of disturbing side effects. In order to achieve a satisfactory compromise it is necessary to gain a deeper understanding of the complex, high dynamic vibrations system "vehicle / drive train". For several years the ika has been carrying out such detailed vehicle investigations and test bench measurements in addition to comprehensive CAE analysis for various research projects in partnership with different vehicle manufacturers.

The air pollution by the diesel locomotives has become serious environmental concern because the emission gases are exhausted without any further treatment. Recently, the public interest on the air pollutants emission reduction technology is increasing due to the establishment of 'Metropolitan Air Quality Preservative Law' and the regulation of local governments on the urban air quality. In this study, we measured the concentration of particulate matters and gaseous pollutants by using a scanning mobility particle sizer, a dust spectrometer, and a stack sampler upon various engine load condition. The results show that the amount of emitted air pollutants increased upon the increase of engine power. The development of new technology to reduce the air pollutants emission is urgently required.

The purpose of this study is to investigate the effect of water injection on combustion characteristics of gasoline direct injection (GDI) engine with turbo-charger under low-load operating condition. The test engine used in this study has four-cylinder and 10.2 of compression ratio. In order to study the effect of water injection ratio on combustion characteristics, the water was injected into the intake port from 10% to 50%, based on fuel injection quantity. From the experiment, it revealed that the water injection induced the improvement of fuel economy because of the advance of spark-timing by the reduction of in-cylinder temperature. In addition, the water injection caused the prolong of extension of the ignition delay and slight increase of burn duration.

Modern diesel vehicle has to comply with the EURO IV, V regulation with low level of particulate matter and smoke emission Moreover, emission standards of each countries are becoming stringent in advanced countries such as USA and Europe. Because Bio-diesel is similar to diesel fuel, it is essential to judge the environmental and health effects deriving from the use of Bio-diesel in diesel engine. The deterioration characteristics of emission in accordance with aging vehicles must be regulated for Bio-diesel. Therefore, under 1200 driving hours, 220,000km driving distance condition and full load, the deterioration characteristics of emission were estimated. We could reduce sulfur contents of fuel, particulate matter and smoke emission by using Bio-diesel and conform the influence of engine performance, emission, and fuel consumption by Bio-diesel deterioration

The aim of this study was to measure and analyze engine load factor (LF) according to working conditions (operation type and gear stage) of small agricultural multi-purpose cultivator to estimate the emission of air pollutants. To calculate LF, a torque sensor capable of collecting torque and rotational speed was installed on the engine output shaft and DAQ was used to collect data. A field test was conducted with major operation of a cultivator and tillage operations (plow tillage and rotary tillage). Engine power was calculated using engine torque and rotational speed and LF was calculated using real-time power and rated power. In addition, unified LF was calculated using the weight for each operation and the average LF for each operation. As a result, average LF values at 1.87 and 3.10 km/h by plow tillage were 0.50 and 0.69, respectively. Average LF values at 1.87 and 3.10 km/h by rotary tillage were 0.70 and 0.78, respectively. Furthermore, unified LF calculated in consideration of the weight factor showed a value of 0.65, which was 135% higher than the conventional LF (0.48). Results of this study could be used as basic information for realizing LF values in the field of agricultural machinery.

The purpose of this study was to calculate and analyze the engine load factor of major agricultural operations using a 78 kW class agricultural tractor for estimating the emission of air pollutants and greenhouse. Engine load data were collected using controller area network (CAN) communication. Main agricultural operations were selected as plow tillage (PT), rotary tillage (RT), baler operation (BO), loader operation (LO), driving on soil (DS), and driving on concrete (DC). The engine power was calculated using the measured engine load data. A weight factor was applied to load factor for considering usage ratio according to agricultural operations. Weight factors for different agricultural operations were calculated to be 27.4%, 32.9%, 17.5%, 7.7%, 4.5%, and 10.0% for PT, RT, BO, LO, DS, and DC, respectively. As a result of the field test, load factors were 0.74, 0.93, 0.41, 0.23, 0.27, and 0.21 for PT, RT, BO, LO, DS, and DC, respectively. The engine load factor was the highest for RT. Finally, as a result of applying the weight factor for usage ratio of agricultural operations, the integrated engine load factor was estimated to be 0.63, which was about 1.31 times higher than the conventional applied load factor of 0.48. In future studies, we plan to analyze the engine load factor by considering various horsepower and working conditions of the tractor.

This is a basic study analyzing emissions of an agricultural tractor during tillage operations. In this study, CO, THC, NOx, and PM considered as emission factor were analyzed during plow and rotary tillage operation by the tractor. Engine torque and rotational speed were measured through ECU. Engine power was calculated using engine torque and rotational speed. The emissions was calculated based on the number of units, rated power, load factor, and operating time. Results showed that the load factor was calculated almost twice, which was higher than 0.48. It was also observed that the emission of the tractor was variable for different agricultural operations because tractor loads were different based on operations. There was a difference in emissions due to differences in plow and rotary working hours. To estimate the emission of agricultural tractor based field operations in detail, it is necessary to consider TAF (Transient Adjustment Factor) and DFA (Deterioration factor). In the future, TAF and DFA will be considered to estimate emissions of the agricultural tractor. Finally, results of this study can contribute to the literature to estimate tractor emissions accurately.

Non-esterified biodiesel fuel is cheaper than esterified that because of a simple manufacturing process that only consists of filtering. Applicability of this on diesel engine with electronic control system was accomplished, then optimization adopting a fractional factorial design and response surface methodology was carried out at 25% and 50% of engine load in this study. Pressure of common rail and injection timing mainly effected on responses as specific fuel oil consumption and nitrogen oxides regardless of engine load. Estimations were 310.3 g/kWh of specific fuel oil consumption and 237 ppm of nitrogen oxides at 25% load, and 233.2 g/kWh of specific fuel oil consumption and 730 ppm of nitrogen oxides at 50% load. Tests to verify these estimations were accomplished and as the results, specific fuel oil consumption was 300.4 g/kWh and NOx was 277 ppm at 25% load and 236.8 g/kWh and 573 ppm at 50% load.

In recent days, LPi system have far better performance than one of conventional vaporizer type with its increase in volumetric efficiency. LPi shows not only the similarity to a gasoline injection type but also the return type that circulates between LPG fuel rail and LPG tank. The return type system reduces the pulsation in a fuel rail and prevents the overload in a fuel pump. However, in case of applying the returnless system that circulate a fuel to LPG Tank, it gives the reduction of production cost in removing the return line. Therefore, in order to examine the suitability of returnless type, we examined the part load characteristics with a dynamometer and THC measurement test with FID(Flame Ionization Detector).

In order to reduce exhaust emissions from diesel engine under wide load range, an experimental study was conducted base on a new concept of combustion, that is, most of the fuel is supplied as premixed homogeneous charge and small amount of diesel fuel directly injected into a cylinder to ignite. In this study we compared combustion caracteristics of HCDC(Homogeneous Charge Disel Combustion) engine with that of commercial diesel engine. At high premixed fuel ratio and high load range, it was observed that premixed combustion temperature was low and diffusion combustion duration was shorten. From this experiment, it could be found the NOx reduction is caused by the lower maximum temperature and soot reduction is caused by rapid combustion under diffusion combustion part.

In this study, three visualization methods, Schlieren, Shadowgraph, and Mie-scattering, were applied to compare diesel and gasoline spray structures. Fuels were injected into a high pressure/high temperature constant volume chamber under the same ambient pressure and temperature condition of low load in gasoline direct injection compression ignition (GDCI) engine. Two injection pressures (40 and 80 MPa), two ambient pressures (4.2 and 1.7 MPa), and two ambient temperatures (908 and 677 K) were use. The images from the different methods were overlapped to show liquid and vapor phases more clearly. It was found that the gasoline fuel is more appropriate to form a lean mixture.