Earticle

본 연구에서는 기지국내 운영되고 있는 각종 통신장비에서 발생하는 발열량을 분석하여 효율적인 운영을 하고 져 한다. 우선발열량이 많이 발생하는 기지국을 선정하여 실제 전력량을 분석하였다. 본 연구에서는 산업 발전을 위해 자연공조를 활용한 다양한 연구가 필요 하다고 볼 수 있다.

본 연구에서는 기지국내 운영되고 있는 각종 통신장비에서 발생하는 발열량을 분석하여 효율적인 운영을 하고 져 한다. 우선 발열량이 많이 발생하는 기지국을 선정하여 실제 전력량을 분석하였다. 본 연구에서는 산업 발전을 위해 자연공조를 활용한 다양한 연구가 필요 하다고 볼 수 있다.

본 연구는 무선기지국내 에너지를 안전하게 절감하여 효율적인 기지국운영을 위하여 본 연구를 분석하게 되었다. 특히 기지 국에는 각종 유･무선 통신장비가 많이 설치되어 있다. 이들은 통신서비스를 위하여 운영하고 있다. 또한 현재 기지국에 운영되 고 있는 냉방장치는 주･예비 2대로 운영되고 있다. 기지국 실내온도는 상온 27℃ 이하로 설정하고 운영 한다. 실내 냉방기운영 은 주장치로 24시간 가동하여 운영 한다. 가끔 기지국은 냉방기 장애가 발생하는 사례가 있다. 그로 인하여 통신서비스 및 각종 데이터통신 장애로 인하여 민원이 발생하는 일이 있다. 각종 통신장비에서 실시간 발생하는 발열을 없애기 위해 냉방기는 주･ 예비 항상 안전운영한다. 기지국내는 항상 최적화한 상태에서 서비스를 하여야 한다. 본 연구에서는 기지국내 운영되고 있는 각종 통신장비에서 발생하는 발열량을 분석하여 효율적인 안전운영을 하고자 한다. 우선 발열량이 많이 발생하는 기지국을 선 정하여 실제 전력량을 분석하였다. 본 연구에서는 산업 발전을 위해 자연공조를 활용한 다양한 연구가 필요 하다고 볼 수 있다.

정보통신 산업 발전에 따라 통신장치의 크기는 소형화 되고 발열량이 많이 발생하는 시스템으로 변화하고 있다. 그러므로 무선기지국에는 무선장비의 발열량이 많이 발생하여 에너지가 계속 많이 소모되고 있고 그로 인하여 무선기 지국의 장애가 발생 할 우려가 있어 본 연구에서는 효율적이고 효과적인 방법으로 무선기지국내 에너지를 절감하고 기지국운영을 위하여 본 연구를 분석하게 되었다. 연구방법으로는 발열량 및 전기료를 많이 발생하는 기지국 대상으로 실시하였고 기지국 25개를 선정하여 2주간 데이터를 확보 하였다. 신뢰성을 확보하기 위해 실내 온도를 일정하게 27℃ 로 유지 하였으며 , 제어시스템을 설치하여 2주간 똑 같이 설치하여 date를 분석 확보 하였다. 연구방법에 있어 시험결 과를 산출하기 위해 계측기는 전산전력계, 디지털온도계, 분진측정 등이 활용하였다. date분석을 위해 Control Sysetm 설치 전 date와 설치 후 date 분석을 위해 25개 무선기지국대상으로 연구 시험 하였다.

With the development of the information communication industry, the size of the communication device has been reduced to a system that generates a large amount of heat. Therefore, since the amount of heat generated by the wireless equipment is large in the wireless base station, the energy consumption is continuously consumed and the failure of the wireless base station may occur. Therefore, in this study, The study was analyzed. As a research method, we performed base station with a lot of calorific value and electric charge. We selected 25 base stations and obtained data for two weeks. To ensure reliability, the room temperature was kept constant at 27 ℃, and the control system was installed and equiped for two weeks to obtain the date analysis. In order to calculate the test results in the study method, the instrument was used with a computer, a digital thermometer, and dust measurement. For the date analysis, we conducted a research study on 25 wireless basestations before and after the installation of Control Sysetm.

Vehicle Stability Control (VSC) system prevents vehicle from spinning or drifting out mainly by braking intervention. Although a control threshold of conventional VSC is designed by vehicle characteristics and centered on average drivers, it can be a redundancy to expert drivers in critical driving conditions. In this study, a manual adaptation of VSC is investigated by changing the control threshold. A control threshold can be determined by phase plane analysis of side slip angle and angular velocity which is established with various vehicle speeds and steering angles. Since vehicle side slip angle is impossible to be obtained by commercially available sensors, a side slip angle is designed and evaluated with test results. By using the estimated value, phase plane analysis is applied to determine control threshold. To evaluate an effect of control threshold, we applied a 23-DOF vehicle nonlinear model with a vehicle planar motion model based sliding controller. Controller gains are tuned as the control threshold changed. A VSC with various control thresholds makes VSC more flexible with respect to individual driver characteristics.

Grid-connected distributed power generation has been widely used in green energy generation. However, due to the distributed characteristics, distributed power generation is difficult to be dynamically allocated and monitored in the electrical control process. In order to solve this problem, this research combined the Internet of Things (IoT) with the automatic control system of electrical engineering to improve the control strategy of the power grid inverter according to the characteristics of the IoT system. In the research, a connection system of the power grid inverter and the IoT controller were designed, and the application effect was tested by simulation experiments. The results showed that the power grid inverter had strong tracking control ability for current and power control. Meanwhile, the electrical control system of the IoT could independently and dynamically control the three-phase current and power. The given value was reached within 50 ms after the step signal was input, which could protect the power grid from being affected by the current. The overall system could realize effective control, dynamic control and protective control.

세계는 급속한 IT 기술의 발달과 생명공학의 발달로 인간 수명이 급격하게 연장되어 노령화가 사회문제가 되는 시대에 살고 있다. 이러한 노령화 문제는 제조공장 또는 물류창고의 물류운송공장에서의 인력을 대신할 수 있는 무인운반 차가 대체로 옮겨지고 있다. 이러한 무인운반차 사용의 증가세는 매년 큰 폭으로 상승하고 있으며, 스마트공장 내에서만 사용하던 무인운반차는 항만의 거대한 컨테이너를 운반할 수 있는 컨테이너 운반용으로 변모하고 있어 실내에서 실외로 그 활용성을 더욱 확장하고 있다. 이렇게 활용도가 증가하고 있는 무인운반차의 중요도가 높아짐에 따라 이를 제어하는 RCS(Remote Control System)의 중요성도 역시 증가하고 있다. 본 연구에서는 무인운반차 RCS의 품질평가체제의 확립을 위해 다양하게 발전하고 있는 무인운반차의 특성과 기술동향 그리고 무인운반차 RCS의 기술적 특징을 조사 분석하여 이를 바탕으로 무인운반차 RCS의 신뢰확보를 위해 국제품질평가 표준인 ISO/IEC 25000 시리즈를 참조하여 기능적합성과 사용 성의 평가항목을 도출하고, 도출된 기능접합성과 사용성의 평가항목을 통해 평가모델을 개발하고자 한다.

With rapid development of IT technology and biotechnology, human lifespan is extended rapidly, and we are living in the era where aging becomes the social issue. Due to this aging problem, manpower is mainly replaced by Automated Guided Vehicles (AGV) in manufacturing factories or warehouse logistics transportation. Rate of AGV use increases sharply every year. AGVs, which were used only in Smart Factories, extends its usage into indoor and outdoor operation by changing their usages to container transportation that can carry huge containers in the harbor. With the expansion of AGVs usage, the importance of RCS (Remote Control System) is also increased. In this study, we surveyed and analyzed the characteristics and technology trends of technical features of AGV's RCS that are developing in various ways to establish quality evaluation system of AGV RCS. Based on this, and by referring to international quality assessment standards, ISO/IEC 25000 series, we derived evaluation items on functional suitability and usability to secure reliability of AGV RCS. Also, it is our intention to develop evaluation model using those derived usability and reliability evaluation items.

Transportation allocation requires information such as storage location and order information. In order to guarantee the safe transmission and real-time sharing of information in all links, an intelligent transportation control system based on blockchain technology is designed. Firstly, the technical architecture of intelligent transportation information traceability blockchain and the overall architecture of intelligent transportation control system were designed. Secondly, the transportation management demand module and storage demand management module were designed, and the control process of each module was given. Then, the type of intelligent transportation vehicle was defined, the objective function of intelligent transportation control was designed, and the objective function of intelligent transportation control was constructed. Finally, the intelligent transportation control was realized by genetic algorithm. It was found that when the transportation order volume was 50×103, and the CPU occupancy of the designed system was only 11.8%. The reliability attenuation of the code deletion scheme was lower, indicating better performance of the designed system.

Reducing aircraft speed is the important task in the Rejected Takeoff and/or landing process. It is known that the effect of the Speedbrake is most important factor during the rejected takeoff maneuver in particular near V1 on the critical field length runway. The B747 designer created Automatic Speedbrake Control System to relieve pilot workload, improves brake operation and ensures proper Speedbrake operation for rejected take off. However, those who make the Rejected Takeoff procedure ignored the Automatic function and made it does all manual operations. This lets procedures difficult, complicated, and a cause of confusion and pilot error. This study was conducted to commentary the mechanism and function of the Automatic Speedbrake Control System of B747-8 and to propose appropriate B747-8 Rejected Take off procedures for its function to reduce the workload of pilots and contribute to reduce the possibility of pilot error during Rejected Takeoff.

This paper presents a linear positioning system and its control algorithm design with nano accuracy/resolution. The basic linear stage structure is driven by an ultrasonic motor and its displacement feedback is detected by a LDGI (Laser Diffraction Grating Interferometer), which can achieve nanometer resolution. Due to the friction driving property of the ultrasonic motor, the driving situation differs in various ranges along the travel. Experiments have been carried out in order to observe and realize the phenomena of the three main driving modes: AC mode (for mm motion), Gate mode (for ${\mu}m$ motion), and DC mode (for nm motion). A proposed FCMAC (Fuzzy Cerebella Model Articulation Controller) control algorithm is implemented for manipulating and predicting the velocity variation during the motion of each mode respectively. The PCbased integral positioning system is built up with a NI DAQ Device by a BCB (Borland $C^{++}$ Builder) program to accomplish the purpose of an intelligent nanopositioning control.

In this study, we constructed several scenarios that are required for LED lighting, and we designed and implemented an LED lighting control system to operate these scenarios to confirm their behavior. An LED lighting control system is a hybrid control board that is designed by combining LED controllers and SMPS, consisting of an AC/DC power supply part that converts AC 220 V into DC 12 V, and a drive and control part that controls the scenario and color of the LED module. Conventional LED light controllers have an input power of DC 12 V, so when using the input AC 220 V, the SMPS must be connected to the LED light controller. To eliminate this inconvenience, a hybrid LED lighting control system was configured to combine LED lighting controllers and SMPS into one control system. Furthermore, we designed a control system to represent the most appropriate color according to the input of the distance and illumination using a fuzzy control system to conduct computer simulations.

A remote control system (RCS) can monitor a user's confidential information by using the broadcast receivers in Android OS. However, the current RCS detection methods are based only on a virus vaccine. Therefore, if the user's smartphone is infected by a brand new RCS, these methods cannot detect this new RCS immediately. In this paper, we present a secure message transmission medium. This medium is completely isolated from networks and can communicate securely through a QR code channel by using symmetric key cryptography such as the AES block cipher and public key cryptography such as elliptic curve cryptography for providing security. Therefore, the RCS cannot detect any confidential information. This approach is completely immune to any RCS attacks. Furthermore, we present a secure QR code-based key exchange protocol by using the elliptic curve Diffie-Hellman method and message transmission protocols; the proposed protocol has high usability and is very secure.

The development of technology provides and increases security as well as convenience for humans. The development of new technology directly affects the standard of life thanks to smart home automatic control systems. This paper describes a door control, automatic curtain, home security (CCTV, fire, gas, safe, etc.), home control (energy, light, ventilation, etc.) and web-based smart home automatic controller. It also describes the use of ARM (Advanced RISC Machines) for automatic control of home equipment, a Multi-Axes Servo Controller using FPGA (Field Programmable Gate Array) and PLC (programmable logic controller). Additionally, it describes the development of a HTML editor using web auto control software. The tab loading time (7 seconds) is faster when using ARM-based web browser software instead of Chrome and Firefox is used because the browser has a small memory footprint (300M). This system is realized by web auto controller language which controls and uses PLCs that are easier than existing devices. This smart home automatic control technology can control smart home equipment anywhere and anytime and provides a remote interface through mobile equipment.

In the U.S., performance assessment on the Automatic Exposure Control system (AEC) is managed according to the Mammography Quality Standards Act (MQSA). However, The AEC is not available in the performance assessment conducted in Korea. Also, there is no study made on the performance of the automatic exposure control system for mammography in Korea. For this reason, this study examined the performance of the automatic exposure control system for mammography that was clinically used in the Incheon area. Result showed that the difference of the mean optical density was 0.79 ~ 2.81. This implies that some devices caused unnecessary x-ray exposure to patients. Furthermore, only 61.5% of the entire experimental device was shown to be satisfactory in terms of change in mean optical density. Moreover, in terms of the subject's thickness, change in radiographic density was shown to be severe among lower X-ray tube voltage while there was severe density change in X-ray image depending on X-ray tube voltage among the subjects with more thickness. Therefore, it is suggested to provide performance management on the AEC for mammography.

Gears, crucial components in modern precision machinery for power transmission mechanisms, are required to have low contacting noise with high torque transmission, which makes the use of gear-tooth profile modifications and gear-tooth surface crowning extremely efficient and valuable. Due to the shortcomings of current techniques, such as manual rectification, mechanical modification, and numerically controlled rectification, we propose a novel electrochemical gear-tooth profile modification method based on an artificial neural network control technique. The fundamentals of electrochemical tooth-profile modifications based on real-time control and a mathematical model of the process are discussed in detail. Due to the complex and uncertain relationships among the machining parameters of electrochemical tooth-profile modification processes, we used an artificial neural network to determine the required processing electric current as the tooth-profile modification requirements were supplied. The system was implemented and a practical example was used to demonstrate that this technology is feasible and has potential applications in the production of precision machinery.

The lane departure avoidance systems have been considered promising to assist human drivers in AVCS (Advanced Vehicle Control System). In this paper, a lane departure monitoring and control system is developed and evaluated in the hardware-in-the-loop simulations. This system consists of lane sensing, lane departure monitoring and active steering control subsystems. The road image is obtained based on a vision sensor and the lane parameters are estimated using image processing and Kalman Filter technique. The active steering controller for avoiding the lane departure is designed based on the lane departure metric. The proposed lane departure avoidance system is realized in a steering HILS (hardware-in-the-loop simulation) tool and its performance is evaluated with a driver in the loop.

Owing to the convergence of the communication network with the control system and public network, security threats, such as information leakage and falsification, have become possible through various routes. If we examine closely at the security type of the current control system, the operation of the security system focuses on the threats made from outside to inside, so the study on the detection system of the security threats conducted by insiders is inadequate. Thus, this study, based on "Spotting the Adversary with Windows Event Log Monitoring," published by the National Security Agency, found that event logs can be utilized for the detection and maneuver of threats conducted by insiders, by analyzing the validity of detecting insider threats to the control system with the list of important event logs.

The existing electrical engineering design method and the dynamic objective function in the application process of automatic control system fail to meet the unbounded condition, which affects the control tracking accuracy. In order to improve the tracking control accuracy, this paper studies the electrical engineering design method based on neural network and the application of automatic control system. This paper analyzes the structure and working mechanism of electrical engineering automation control system by an automation control model with main control objectives. Following the analysis, an optimal solution of controllability design and fault-tolerant control is figured out. The automatic control power coefficient is distributed based on an ideal control effect of system. According to the distribution results, an automatic control algorithm is based on neural network for accurate control. The experimental results show that the electrical automation control method based on neural network can significantly reduce the control following error to 3.62%, improve the accuracy of the electrical automation tracking control, thus meeting the actual production needs of electrical engineering automation control system.

In this paper, a new revolute mobile robot arm with five degree of freedom (d.o.f) was developed for autonomous moving robots. As a control system for the robot arm, a distributed control system composed of the main controller and five motor controllers for arm joints was developed. The main controller and the motor controllers w ε re developed using the ARM microprocessor and the TMS320c2407 microprocessor, respectively. A new trajectory tracking algorithm for the motor controllers was devised employing pre-generated off-line trajectory data. Also, a 3-D simulator based on the openGL software to simulate the motion of the robot arm was developed. To validate the performance of the robot system, experiments to track a specified trajectory were performed.