Earticle

A real-time control device for railway vehicle simulation is designed in this study according to the experimental requirements of a railway vehicle electric traction and electric braking system. The device uses the high-speed processing characteristic of DSP and runs on the basis of both DSP and the corresponding experimental platform. The simulation experiment for a different power grade traction system is achieved through control of the device. Full static and dynamic simulation of the operating condition of the train electric traction and braking system is attained in the case of no commissioning.

There are three different well-known methods for predicting the manoeuvrability of ships: (1) free running model test, (2) direct manoeuvring simulation using CFD and (3) system-based manoeuvring simulation. In this paper, the manoeuvrability of the KVLCC2 was estimated using CFD with rigid body motion and body force propeller method. The free running manoeuvre at the different time steps were also simulated. The yaw checking ability and the turning ability of KVLCC2 were predicted using CFD and could have been confirmed that the IMO criteria was satisfied. When the results were compared with the model test and system-based method, the free running simulation showed better agreement to that of the model test. It could also be confirmed that the results vary depending on the time step. Overall, the CFD results using the body force propeller method estimated most accurately the test results.

There is much room for consideration that the magnet design of UTM. When the vehicle runs 60mR curved line on test track, the ratio of cross section area changed to cross the magnet pole and rail. The ratio is reduced about 20% of the total magnet on one bogie. Therefor, magnet current is increased about 3.5A to maintain constant air gap. This paper suggest to margin of the magent design is 1.1 rather than rated levitation force.

The present investigate is a base investigate required in development of DMT wagon train. And it deduced that follows by developing trail analysis model about Modalohr wagon train and examining traveling movement specific using analysis model developed. Vibration acceleration of all direction was increased with addition of travel speed and first suspension. But in case of right and left vibration acceleration, that could influenced by nonlinear specific of first suspension. Therefore checking about those is needed. Frequency of $2{\sim}3\;Hz$ and $7{\sim}8\;Hz$ generated in Right and left, up, down vibration of vehicle. And right and left vibration of bogie generated $25{\sim}35\;Hz$ in low speed section and frequency of $40{\sim}50\;Hz$ in high speed section, $25{\sim}35\;Hz$ in low speed section, $10{\sim}15$ or $40{\sim}50\;Hz$ in high speed section.

Maglev vehicles, which are levitated and propelled by electromagnets, often run on elevated flexible guideways comprised of steel, aluminum and concrete. Therefore. an analysis of the dynamic interaction between the Maglev vehicle and the flexible guideway is needed in the design of the critical speed, ride, controler design and weight reduction of the vehicle. This study introduces a dynamic interaction simulation technique that applies structural dynamics. Because the proposed method uses FEM, it is useful to calculate the deformation of the elevated flexible guideway, the dynamic stress, and the motion of the vehicle. By applying the proposed method to an urban transit Maglev vehicle, UTM01, the dynamic response is simulated and validated. From the result of the study, we concluded, that the dynamic interaction between the maglev vehicle and the flexible guideway is possible.

When a planing hull straightly runs and turns, its floating position and pitch angle are changed depending on its speed, and large transient motion happens. In this paper, six degrees of freedom(6 DOF) equations of motion, which could simulate the motion of a planing hull, are established. Static and dynamic forces in vertical plane are modeled using pre-calculated displacements and metacentric heights depending on various draft, lift under bottom, and vertical damping coefficients which are used to tune the final motion. Hydrodynamic coefficients in horizontal plane at various equilibrium state are calculated by using Lewandowski's empirical formula and the speed-dependent equilibrium state are calculated beforehand by Savitsky's formula. The speed effects are considered by curve-fitting the coefficients at various speed to the polynomials. Accelerating, decelerating and backing, turning, and zig-zag are simulated and compared with the sea trial results, and it is confirmed that the speed reduction, roll, and pitch during such maneuvers of sea trial and simulation are well consistent.

When a planing hull straightly runs and turns, its floating position and pitch angle are changed depending on its speed, and large transient motion happens. In this paper, six degrees of freedom(6 DOF) equations of motion, which could simulate the motion of a planing hull, are established. Static and dynamic forces in vertical plane are modeled using pre-calculated displacements and metacentric heights depending on various draft, lift under bottom, and vertical damping coefficients which are used to tune the final motion. Hydrodynamic coefficients in horizontal plane at various equilibrium state are calculated by using Lewandowski's empirical formula and the speed-dependent equilibrium state are calculated beforehand by Savitsky's formula. The speed effects are considered by curve-fitting the coefficients at various speed to the polynomials. Accelerating, decelerating and backing, turning, and zig-zag are simulated and compared with the sea trial results, and it is confirmed that the speed reduction, roll, and pitch during such maneuvers of sea trial and simulation are well consistent.