Earticle

연구목적: 본 연구에서는 탄소성해석과 수치해석의 차이점 분석과 해석 결과치의 유사한 경향을 도출 하기 위한 설계지반정수 재산정 방법의 연구를 수행하였다. 연구방법: 얕은굴착과 깊은굴착에 따라 벽 체변위가 같아지는 시점에서의 지반반력계수와 지반변형계수의 관계식을 유도하였다. 연구결과: 계측 결과를 바탕으로 역해석을 진행하여 현장지반에 맞는 지반물성을 재산정하고 도출된 식과 문헌식을 이용하여 벽체변위에 대한 비교·검증한 결과 제안식이 가장 유사한 값을 나타내고 있었다. 결론: 제안 식을 이용하면 설계시 실제와 가장 비슷한 지반물성치를 유추할 수 있어 실무에 도움이 될 것이다.

Purpose: In this study, an analysis of the differences between the elastoplastic analysis and the numerical analysis and a study of the design ground constant recalculation method to derive similar trends in the analysis results were conducted. Method: The relational expression between the ground reaction force coefficient and the ground deformation coefficient at the time when the wall displacement becomes the same according to shallow excavation and deep excavation was derived. Result: Based on the measurement results, reverse analysis was performed to re-calculate the ground properties suitable for the site ground, and as a result of comparing and verifying the wall displacement using the derived formula and the literature formula, the proposed formula showed the most similar value. Conclusion: If the proposed formula is used, it will be helpful in practice because it is possible to infer the most similar ground properties to the actual at the time of design.v

Purpose: This study is a mechanical strength supplementation of denture base resin Polymethyl methacrylate (PMMA) is in general use for denture base resin of the partial and full denture, however, The polymerization process of PMMA is not stabilized. Because of compatibility problems, preceding studies were performed, which were enhancing mechanical strength(Camilo Machado 2007),(Ana M. 2008), addition filler to materials property(Ayse Mese, 2008), self curing method(Hiroshi Shimizu, 2008). Methods: The carbon fiber and polyacetal filler, reinforced the mechanical strength for improving the stability of denture base resin were supplemented to the self cured resin. The Modulus of elasticity and the restoring force were calculated by tensile test. Results: The strengths of the heat and self cured resin were respectively decreased and increased, when the filler was supplemented to the denture base resin and the modulus of elasticity of both heat and self cured resin were not increased, when the filler was supplemented to the denture base resin. Conclusion: The restoring forces of self cured resin containing 10% filler were increased, when the filler was supplemented to the denture base resin.

Sealants cause problem that exfoliation with surface and breaking of sealants by a change of temperature, humidity and wind pressure according as time passes. In this study, it was intended to provide solution for choose a sealant which satisfy the requirement on the joint when sealing construction. For this purpose, after producing experimental specimens, tests were performed to analyze the elongation and adhesive strength according to the kind of sealants and surface. The result of this study, the elongation, adhesive strength and modulus of elasticity show wide difference depending on the kind of sealant without related surface material. Therefore, sealing construction need appropriate use according to sealant type.

본 연구는 건축물의 공기단축을 위하여 조기 거푸집 탈형으로 인한 과대 처짐이 예측될 경우를 고려한 조강형 콘크리트의 탄성계수 발현특성을 실험실적으로 확인하였다. 연구결과, 조강형 콘크리트는 보통 콘크리트에 비하여 처짐에 대하여 유리함 것으로 평가되었다.

In this study, The development characteristic of Modulus of Elasticity required to considering large deflection due to early the removal of forms for the reduction of working period of concrete is investigated. As a result of this study, it is found that the high early strength concrete is advantageous to compare with plain concrete on the early deflection.

Aggregates mineralogical, and petrographic properties directly affect the mechanical properties of the produced high strength. This study is focused on the effects of magmatic, sedimentary, and metamorphic aggregates on the performance of high strength concrete. In this study, the effect of the mineralogical properties of aggregates on the compressive strength and modulus of elasticity of high-strength concrete was estimated by Artifical Neural Network (ANN). To estimate the compressive strength and elasticity modules, 96 test specimens were produced. After 28 days under suitable conditions, tests were carried out to determine the compressive strength and modulus of elasticity of the test specimens. This study also focused on the application of artificial neural networks (ANN) to predict the 28-day compressive strength and the modulus of elasticity of high-strength concrete. An ANN model is developed, trained, and tested by using the available test data obtained from the experimental studies. The ANN model is found to predict the modulus of elasticity, and 28 days compressive strength of high strength concrete well, within the ranges of the input parameters. These comparisons show that ANNs have a strong potential to predict the compressive strength and modulus of elasticity of high-strength concrete over the range of input parameters considered.

A new model of generalized thermoelasticity equations for isotropic media with temperature-dependent mechanical properties is established. The modulus of elasticity is taken as a linear function of reference temperature. The present model is described both generalizations, Lord Shulman (L-S) theory with one relaxation time and Green-Lindsay (G-L) with two relaxation times, as well as the coupled theory, instantaneously. The method of the matrix exponential, which constitutes the basis of the state space approach of modern control theory, applied to two-dimensional equations. Laplace and Fourier integral transforms are used. The resulting formulation is applied to a problem of a thick plate subject to heating on parts of the upper and lower surfaces of the plate that varies exponentially with time. Numerical results are given and illustrated graphically for the problem considered. A comparison was made with the results obtained in case of temperature-independent modulus of elasticity in each theory.

국산재에 대한 전단탄성계수와 실질탄성계수를 구하기 위해 서로 다른 세장비에 대한 휨강도실험 및 응력파실험을 실시했다. 국산재의 휨 성질들은 12%로 조습 처리된 무결점 시편으로 측정하였다. 휨강도와 탄성계수는 세장비(L/D)에 영향을 받아 세장비가 증가하면 증가하였다. 전단탄성계수(G)와 실질탄성계수는 서로 다른 세장비에 대한 휨강도 실험 및 응력파실험의 결과를 이용하여 계산했고, 그 값들은 국산재가 구조용도로 사용된다면 유용할 것이다. 하지만 이들 결과들은 제한된 수의 시편들에 대한 값으로 이들 수종의 실질 평균값을 나타내진 않는다.

This study examined true modulus of elasticity (MOE) and modulus of rigidity (G) for domestic woods with different slenderness ratios (L/D) using the static bending and stress wave tests. Bending properties of small clear wood specimen of three domestic wood species were determined at 12% moisture content. The results of this study indicated that both MOR and MOE of domestic woods were affected by the slenderness ratio. As the slenderness ratio increased, MOR and MOE increased. G and true MOE of domestic timber beams were obtained at different slenderness ratios by flexure test and stress wave test. The values reported here can be useful if these species woods are used for structural purposes. However, the reported values are only indicative and do not represent the true average of wood species due to the limited number of specimens tested.

This study was performed to find out the regression function to calculate the modulus of elasticity of concrete mixed by river coarse aggregate. The distribution of the group of core strength made a normal curve and the effect factor in the modulus of elasticity was 0.97 at the concrete compounded by river coarse aggregate.

이 연구에서는 선행연구의 녹차-목재섬유 복합보드에 부가하여, 목제품 생산 후 발생하는 부산물인 편백나무 톱밥의 효율적인 이용과 건축내장재로의 응용을 목표로 목재섬유와 편백톱밥 및 녹차를 혼합한 복합보드를 제조하여 동적탄성률에 미치는 톱밥 및 녹차 배합비율의 영향 및 동적탄성률로부터 정적 휨강도성능의 예측가능성을 평가하였다. 목재섬유-톱밥-녹차 복합보드의 동적탄성률은 1.41~1.65 GPa의 범위에 있었고, 목재섬유: 톱밥: 녹차의 배합비율 50 : 40 : 10에서 가장 높은 값을 나타내었다. 이 값은 정적 휨 탄성계수의 1.4~1.6배의 높은 값을 나타내었고, 녹차-목재섬유복합보드보다 2.0~2.9배 낮은 값을 나타내었다. 동적탄성률과 정적 휨 강도성능과의 상관회귀에서는 일부 예외를 제외하고 대부분 매우 높은 상관계수가 확인되어, 양단자유 휨 진동에 의한 동적탄성률로부터 정적 휨강도성능의 예측이 비파괴적으로 가능할 것으로 사료된다.

In this study, in addition to the green tea - wood fiber hybrid composite boards of previous researches, to make effective use of saw dust of domestic cypress tree with functionalities and application as interior materials, eco-friendly hybrid composite boards were manufactured from wood fiber, green tea and saw dust of cypress tree. We investigated the effect of the component ratio of saw dust and green tea on dynamic MOE (modulus of elasticity). Dynamic MOE was within 1.41~1.65 GPa, and showed the highest value in wood fiber : green tea : saw dust = 50 : 40 : 10 of the component ratio, and had the lowest value in 50 : 30 : 20 of component ratio. These values were 1.4~1.6 times higher than static bending MOE of wood fiber - saw dust - green tea hybrid composite boards, and were 2.0~2.9 times lower than those of green tea - wood fiber hybrid composite boards reported in the previous researches. From the results of correlation regression analyses between dynamic MOE and static strength performances, a very high correlation coefficients were obtained, therefore it was found that static bending strength performances can be estimated with a high reliability from dynamic MOE.

이 연구에서는 녹차-목재섬유 복합보드에 강도성능과 기능성을 보강한 건축내장재를 개발하기 위하여 목재섬유에 녹차와 3종류의 숯을 혼합한 녹차-숯-목재섬유 복합보드를 제작하였고, 구성원료의 종류 및 그 배합비율이 복합보드의 동적탄성률에 미치는 영향을 조사하였다. 또한, 동적탄성률을 이용하여 비파괴적으로 정적 휨강도성능을 예측하였다. 녹차-숯-목재섬유 복합보드의 동적탄성률은 백탄함유 복합보드에서 전체적으로 약간 우수하였으나, 숯의 종류에 따른 차이는 크지 않았다. 녹차와 숯의 배합비율이 증가할수록 복합보드의 동적탄성률의 감소하였다. E1급 요소수지를 사용한 복합보드가 E0급 요소수지를 사용한 그것보다 높은 동적탄성률을 나타내었으나, 양수지간의 차이는 녹차-목재섬유 복합보드에 비해 현저히 적었고, 녹차-목재섬유 복합보드보다 현저한 동적탄성률의 향상을 나타내는 것이 확인되었다. 복합보드의 동적탄성률과 정적 휨 강도성능사이에 대부분 1%의 신뢰수준의 상관관계가 확인되어, 동적탄성률로부터 정적 휨 강도성능이 예측이 가능하였다.

In this study, eco-friendly hybrid composite boards were manufactured from green tea, 3 kinds of charcoals and wood fiber for developing interior materials to reinforce the strength performances and the functionalities in addition to performances of the hybrid composite boards composed of green tea and wood fiber. The effects for the kind and the component ratio of raw materials on dynamic MOE (modulus of elasticity) were investigated, and static bending strength performances were nondestructively estimated. Dynamic MOEs were highest in the hybrid composite boards composed of green tea, fine charcoal and wood fiber on the whole. However, the difference caused by the kind of charcoals was small. These values decreased with increasing component ratios of green tea and charcoals. The hybrid composite boards using E1 grade urea resin had the higher values than those using E0 grade urea resin, however the difference between them markedly decreased than that of hybrid composite board composed of green tea and wood fiber, and it was found that these values were markedly improved than those of the hybrid composite boards composed of green tea and wood fiber. There were mostly high correlations with significance at 1% level between dynamic MOEs and static bending strength performances, and this means that the static bending strength performances can be estimated from dynamic MOE.

본 연구에서는 전통 목조 건축물의 주재료인 목재를 인공 촉진 열화 시킨 후 초음파 전달 속도 측정을 통하여 탄성계수를 측정하였다. 촉진 열화 시간은 0시간에서 500, 1000, 1500, 2000시간이며, 자외선 조사와 주기적인 인공 강우를 통해 열화를 진행시켰다. 초음파 전달 속도 측정을 통하여 동적 탄성 계수를 평가하고 이를 3점 휨 시험을 통하여 측정한 정적 탄성계수와 비교분석하였다. 초음파 전달 속도, 정적 탄성계수, 동적 탄성계수는 열화 시간이 증가함에 따라 동일한 경향을 나타내었는데, 열화 1000시간까지는 탄성계수가 감소하다가 1500시간 이후 다시 회복되는 경향을 보였다. 이러한 결과는 비파괴 검사법을 통하여 전통 목조 건축물의 구조 부재의 열화 평가는 물론 구조 안전성 평가의 기초 자료로 활용될 수 있음을 알려준다.

In this study, accelerated weathering test was performed with wood, a major material for wooden cultural building. In order to evaluate the deterioration of wood, ultrasonic transmission times were measured to evaluate dynamic modulus of elasticity (MOE), which was verified by determining static MOE using three-point bending test. Ultrasonic transmission time was decreased with an increase in the weathering time levels (0, 500, 1000 hours) while it increased in 1500 and 2000 hours. Distribution of dynamic and static MOE was similar to that of the ultrasonic transmission time measurements. The results mean that the measurement of ultrasonic transmission time was very effective to evaluate MOE of wooden cultural buildings for their preservation and management. This method could be utilized to assess wooden cultural buildings as a way of preserving them in a scientific manner.

This paper report the effects of mix ingredients on the modulus of elasticity of high-strength concrete. The test of 284 cylinder specimens are conducted for type I with 10% replacement of fly-ash cement concretes. Different water-binder ratio, amounts of water and coarse aggregate as variables were investigated. And also analyzed it statistically by using SAS.

이 연구에서는 목재의 효율적인 이용과 그 이용확대를 목적으로, 가문비나무를 이용한 직교형 적층재를 제작하였고, 동적탄성계수에 미치는 섬유직각방향라미나의 연륜경각의 영향을 조사하였다. 또한, 동적탄성계수로부터 정적 휨 강도성능을 예측하였다. 3층 모두가 섬유직각방향라미나로 구성된 평행형적층재(P⊥타입)의 동적탄성계수는 연륜경각의 영향이 현저히 나타났고, 연륜경각90∘에서 가장 높은 값을 나타내었고, 45∘에서 가장 낮은 값을 나타내었다. 중층에 섬유방향라미나를 배열하는 것에 의해 동적탄성계수는 현저히 향상되었다. 표층에 섬유직각방향라미나로 구성된 직교형 적층재 (C⊥타입)의 경우, 동적탄성계수는 연륜경각 90∘>0∘>45∘의 순이었으나, 연륜경각에 의한 차이는 평행형 적층재에 비해 현저히 감소하였다. 중층에 섬유직각방향라미나를 배열한 직교형 적층재 (C∥ 타입)의 경우, 동적탄성계수는 P⊥타입 및 C⊥타입과 역으로 연륜경각 45∘에서 가장 높은 값을 나타내었고, 그 값은 P∥ 타입보다 약간 적은 값을 나타내는 것이 확인되었다. 동적탄성계수와 정적 휨강도성능과의 상관회귀의 결과로부터 평행형 및 직교형 적층재의 정적 휨 강도성능이 동적탄성계수로부터 예측 가능한 것이 확인되었다. 단 C⊥타입의 경우, 충분한 시험편의 개수로 상관회귀를 실시할 필요가 있었다.

To study an effective use and extension of utilization of woods, cross-laminated woods were made with spruce wood, and the effects of annual ring angles of perpendicular direction laminae on dynamic modulus of elasticity (MOE) were investigated, and static bending strength performances were estimated from dynamic MOE. Dynamic MOE of parallel laminated woods with all layers composed of laminae perpendicular to the grain (P⊥ type) depended much on annual ring angles, and it was highest in 90? annual ring angle, and was lowest in 45? annual ring angle. By placing longitudinal-direction laminae in the core, the dynamic MOE was markedly improved. In the case of cross-laminated woods with perpendicular-direction laminae in the faces (C⊥ type), the dynamic MOE was in the order of 90?> 0?> 45?, but the differences among annual ring angles were less than that of the parallel-laminated woods. In the case of cross-laminated woods with perpendicular-direction laminae in the core (C∥ type), the dynamic MOE showed the highest value in 45? annual ring angle inversely from P⊥ type and C⊥ type. From the results of regression analyses between dynamic MOE and static strength performances, it was found that static bending strength performances can be estimated from the dynamic MOE.

This study suggests the tangent modulus $E_t$ associated with partially yielded section of steel member under axially compressed. The provisions for column strength does not provide a information about failure mode of structural system. So, designers can not evaluate that a failure comes from member buckling or material yielding. The material of the axially compressed column under inelastic behavior reaches yielding point before the axial force renders the column bent. If axial members yields not by buckling effect but gradually yielding effect of material, the design code should accept related tangent modulus Et which is based on gradual yielding effect of material. This study provides the new effective tangent modulus $E_t$ derived in the case that residual stress is 30 percent and 50 percent of yielding stress respectively. The study considers idealized I section of steel which ignores web and general I section of steel with web respectively and makes conclude that tangent modulus $E_t$ with idealized I section of steel is rational.

가공배전선로의 이도는 탄성계수와 선팽계수에 따라 온도 및 장력의 변화에 대하여 다른 변화를 나타낸다. 따라서 본 연구에서는 정확한 이도설계와 선로의 장기신뢰성 확보를 위해 배전선 주요 규격에 대하여 탄성계수와 선팽창계수를 실측하여 계산값과 측정값에 어떠한 차이가 있는지를 비교하였다. 시험결과 전선의 탄성계수와 선팽창계수는 제작공정상의 여러 요인들에 의하여 영향을 받는 것으로 나타났으며, 이도설계시 탄성계수와 선팽창계수는 배전선의 측정값을 적용하는 것이 바람직 한 것으로 나타났다.

콘크리트의 압축강도 추정에 널리 사용하는 반발경도법을 이용하여 콘크리트 표면의 동해손상을 초기에 판정할 수 있는 가능성을 검토하고자 하였다. 이를 위하여 동결융해 열화조건에 다면으로 노출된 콘크리트와 단면으로 노출된 콘크리트에 대하여 반발경도와 상대동탄성계수를 측정하여 콘크리트 표면 손상도를 비교하였다. 반발경도에 의한 동해손상이 단면 노출 콘크리트 시험체에 대해서는 150싸이클 빠르게 계측되었으며, 다면 노출 시험체에 대해서는 50싸이클 빠르게 계측되었다. 따라서 반발경도법이 공명진동법보다 콘크리트 표면 손상을 신속하게 판정할 수 있는 것으로 사료된다

This study investigated the possibility of early determination of frost damage on the concrete surface by using the rebound hardness method, widely used for estimation the compressive strength of concrete on the site. For this purpose, the surface damage of concrete was compared by measuring the rebound hardness and the relative dynamic modulus of the concrete for the multi-sided and single sided concrete surface exposed to freeze and thaw condition. Compared to the resonance vibration method, the rebound hardness method was able to show the frost damage 150 cycles quicker for the single-sided exposed concrete specimen and 50 cycles quicker for the multi-sided exposed concrete specimen. Therefore, it is considered that the rebound hardness method can determine the concrete surface damage more quickly than that of the resonance vibration method.

This study determines the selection of an appropriate jig material for the blade edge of the medical sapphire knife. The physical properties of the jig material affects the edge shape and chipping phenomenon in machining of the medical sapphire knife. If a grinding wheel is used, brittle workpieces such as sapphire are easily damaged by the propagation of cracks because the grinding force significantly increases. It is important to constantly maintain the grinding force in the grinding process of the brittle materials. The grinding force can be kept constantly by inducing the elastic deformation of the Jig material because the elastic deformation of brittle work-piece is negligibly low. The chipping phenomenon may be reduced by selecting the proper Jig material. Aluminum, copper, stainless steels and carbon steel were used as Jig materials. The experiment was conducted using a cast iron grinding wheel, which was installed on a conventional grinding machine with the ELID grinding system. The thickness and width of the chipping area were measured using an optical microscope and FE-SEM to analyze the shape of the blade edge. According to the experiment result, the chipping phenomenon decreased, and the sharp edge was formed when the jig materials with low elastic modulus were used.

This study focuses on the effect of the elasticity modulus of jig material on blade edge shape in the grinding process of a sapphire medical knife. The ELID grinding process was applied as the edge-grinding method for sapphire material. Carbon steel and copper have been selected as the hard and soft jig materials, respectively. The blade edge created by ELID grinding was measured by a surface roughness tester and optical microscope. The shape of the ground edge and surface roughness were compared using the measurement results. As a result, it was found that chipping in the blade edge of the sapphire knife occurred more than in the case of jig material with a high-elasticity modulus because of the high normal force in the grinding process. Moreover, the maximum height surface roughness, $R_{max}$,of the ground surface was higher in the case of the jig material with a high-elasticity modulus due to the difference in elasticelongation. It was considered to lead to chipping from the notch effect.

최근에 활발히 연구되어지고 있는 UHPC의 경우, 강섬유 혼입량에 의해서 인장강도가 절대적으로 영향을 받는 이유로 본 논문에서는 압축강도, 강섬유량 등을 변수로 하여 압축강도, 탄성계수 및 인장강도 등을 실험적으로 구한 후, 그 결과를 분석하였다. 실험결과에 의하면, 압축강도와 탄성계수 및 인장강도는 비례관계로 상당한 상관성을 가지는 것으로 나타났으며, 섬유혼입률에 따른 압축강도와 인장강도의 관계 역시는 비례관계의 상관성을 가지는 것으로 나타났다. 탄성계수의 경우, 실험결과와 현행 국내 설계기준 식의 차이는 그다지 크지 않은 것으로 나타나, 기존의 설계기준 식을 준용하여도 UHPC 탄성계수 평가에는 큰 문제가 없을 것으로 예상된다. 한편 인장강도의 경우, 현행 설계기준에서 제시되지 않은 이유로 비선형 회귀분석을 실시하여 섬유혼입률을 고려한 인장강도 식을 제안하였으며, 제안된 식은 좋은 상관성을 보이는 것으로 나타났다.

Recently, for UHPC (Ulta High Performance Concrete) which is researched actively, as the tensile strength is absolutely influenced on the content of steel fiber, in this paper, experiments of compressive strength, elasticity modulus and tensile strength were performed according to compressive strength and content of steel fiber as variables. By the test results, compressive strength, elasticity modulus and tensile strength are proportioned and have a good correlation and according to content of steel fiber, compressive and tensile strength are also proportioned and have a good correlation. In case of elasticity modulus, the difference between test and present design code is not large, so it is possible to adapt to present design code. On the other hand, in case of tensile strength, as there is no specification of present design code, new prediction equation is proposed by using nonlinear regression analysis and the proposed equation have a good correlation to test results.