Earticle

Background: The scattered photons cause reduction of the contrast of radiographic image and it results in the degradation of the quality of the image. In order to acquire better quality image, an anti-scattering x-ray gird should be equipped in radiography system. Materials and Methods: The X-ray anti-scattering grid of the inclined type based on the hybrid concept for that of parallel and focused type was tested by MCNP code. The MCNPX 2.7.0 was used for the simulation based test. The geometry for the test was based on the IEC 60627 which was an international standard for diagnostic X-ray imaging equipment-Characteristics of general purpose and mammographic anti-scatter grids. Results and Discussion: The performance of grids with four inclined shielding material types was compared with that of the parallel type. The grid with completely tapered type the best performance where there were little performance difference according to the degree of inclination. Conclusion: It was shown that the grid of inclined type had better performance than that of parallel one.

Background: Radiation protection is crucial in various fields due to the harmful effects of radiation. Shielding is used to reduce radiation exposure, but gamma radiation poses challenges due to its high energy and penetration capabilities. Materials and Methods: This work investigates the radiation shielding properties of polyvinylidene fluoride (PVDF) samples containing different weight fraction of tungsten carbide (WC), tungsten trioxide (WO3), and tungsten disulfide (WS2). Parameters such as the mass attenuation coefficient (MAC), half-value layer (HVL), mean free path (MFP), effective atomic number (Zeff), and macroscopic effective removal cross-section for fast neutrons (ΣR) were calculated using the Phy-X/PSD software. EpiXS simulations were conducted for MAC validation. Results and Discussion: Increasing the weight fraction of the additives resulted in higher MAC values, indicating improved radiation shielding. PVDF–xWC showed the highest percentage increase in MAC values. MFP results indicated that PVDF–0.20WC has the lowest values, suggesting superior shielding properties compared to PVDF–0.20WO3 and PVDF– 0.20WS2. PVDF–0.20WC also exhibited the highest Zeff values, while PVDF–0.20WS2 showed a slightly higher increase in Zeff at energies of 0.662 and 1.333 MeV. PVDF–0.20WC has demonstrated the highest ΣR value, indicating effective shielding against fast neutrons, while PVDF– 0.20WS2 had the lowest ΣR value. The Monte Carlo N-Particle Transport version 5 (MCNP5) simulations showed that PVDF–xWC attenuates gamma radiation more than pure PVDF, significantly decreasing the dose equivalent rate. Conclusion: Overall, this research provides insights into the radiation shielding properties of PVDF mixtures, with PVDF–xWC showing the most promising results.

방사선검출기를 이용한 고방사성물질의 측정이나 방사선사고 등의 신속한 대응을 위하여 주위의 선량률 준위에 따라 크기별로 여러 종류의 콜리메이터들을 구비해야 하며, 이는 무거운 콜리메이터의 특성상 효율적인 현장 측정에 심각한 장애가될 수 있다. 본 연구에서는 콜리메이터의 모양을 카메라의 렌즈 조리개 형식으로 제작하여 사용자가 직접 카메라 렌즈를 돌려 초점을 맞추듯이 콜리메이터의 내경을 조절하고 방사선의 감쇄율을 쉽게 알아볼 수 있도록 IRIS형 콜리메이터를 제작하였다. 먼저, 콜리메이터를 위상을 달리한 2 중의 텅스텐 셔터 구조로 제작하여 기계적 공차에 의한 방사선의 침투를 차단하고자 하였다. 그리고 셔터의 재질별로 콜리메이터 내경에 따른 방사선 감쇄율을 MCNP 코드를 이용하여 계산함으로써 이론적인 성능평가를 수행하였다. 계산된 내경의 크기별 감쇄율을 콜리메이터 외부 눈금링에 표시함으로써, 카메라 렌즈에 표시된 배율과 같은 방법으로 사용자가 해당 표시지점으로 콜리메이터 내경을 조절하였을 때, 방사선의 세기가 얼마만 큼 감소되는지 쉽게 알아볼 수 있도록 구현하였다. 끝으로 개발된 IRIS형 콜리메이터를 장착한 소형 방사선검출기를 현장 측정에 활용할 경우, 콜리메이터의 교체 없이 주위 방사선의 세기에 따라 콜리메이터 내경을 적절한 크기로 신속히 교체가 가능하며,방사선 세기의 감쇄 정도를 쉽게 알아보게 함으로써 신속하고 정확한 대처가 가능할 것으로 판단된다.

When a radiation detector is applied to the measurement of the radioactivity of high-level of radioactive materials or therapid response to the nuclear accident, several collimators with the different inner radii should be prepared according tothe level of dose rate. This makes the in-situ measurement impractical, because of the heavy weight of the collimator. Inthis study, an IRIS collimator was developed so as to have a function of controlling the inner radius, with the same methodused in optical camera, to vary the attenuation ratio of radiation. The shutter was made to have the double tungsten layerswith different phase angles to prevent the radiation from penetrating owing to the mechanical tolerance. The performanceevaluation through the MCNP code was conducted by calculating the attenuation ratio according to the inner radius of thecollimator. The attenuation ratio was marked on the outer scale ring of the collimator. It is expected that when a radiationdetector with the IRIS collimator is used for the in-situ measurement, it can change the attenuation ratio of the incidentphoton to the detector without replacing the collimator.

한국원자력연구원 내 저장중인 중·저준위방사성폐기물의 안전한 영구처분을 위하여 방사성폐기물처 리시설에서는 이들 저장폐기물의 핵종재고량 평가를 위한 드럼핵종분석장치의 도입을 기획하고 있으며, 이 장치를 운영하고 유지보수하기 위한 전용의 평가시설 구축을 추진하고 있다. 이 평가시설 외부에는 제 1방사성폐기물저장시설이 인접하여 있으며 내부에는 평가대상드럼들과 드럼핵종분석장치의 밀도보정용 선원 등이 존재함으로 이들이 방사선원항으로 작용하여 평가시설 내·외부의 선량률에 영향을 미치게 된 다. 따라서 방사선원항 주변의 콘크리트 구조물에 대한 방사선차폐 영향을 평가하여야 한다. 본 연구에서 는 MCNP 코드를 이용하여 해당 방사선원항으로부터 평가시설 내부 방사선관리구역을 둘러싸고 있는 콘 크리트 구조물에 대한 방사선 안전성을 평가하였다. 평가결과 현재 고려되고 있는 콘크리트 구조물의 약 30 cm 두께는 해당 방사선원항으로부터의 방사선을 차폐하기에 충분한 것으로 확인되었다.

In order to dispose of the LILW(low and intermediate level radioactive waste) stored at KAERI, the radwaste drum assay system will be introduced to evaluate the radioisotopes inventory of stored drums. At present, the construction project of the dedicated assay facility to operate it and carry out routine maintenance of that equipment has been conducting at the radwaste treatment facility. Since that facility will be constructed in front of a 1st radwaste storage facility as well as the radwaste drums to be assayed and the transmission source in the radwaste drum assay system are in that facility, they could act as the radioactive sources and then, would affect the dose rate at the inside and the outside of the facility. Therefore, the radiation shielding should be evaluated through the concrete wall near to the radioactive sources whether the wall thickness is sufficient against the regulations. In this study, the radiation safety for the concrete wall around the radiation controlled area in the radwaste drum assay facility was evaluated by the MCNP code. From the evaluation results, the thickness of those concrete walls which are under consideration of about 30 cm was enough to shield the radiation from the radioactive sources.

의료용 선형가속장치의 두부 구성요소 중 광자 발생의 원인이 되는 타깃에 대한 연구로써, 타깃의 재질에 따른 광자를 분석하여 타깃 재질 별 발생하는 광자특성에 대한 기초자료를 제시하고자 한다. 본 연구에서는 몬테카를로 방식을 바탕으로 한 MCNPX를 사용하여 타깃 재질에 따른 6, 15 MV의 광자 특성을 비교분석하였다. 타깃 재질 별 평균에너지는 6 MV에서 1.69 ~ 1.84 MeV, 15 MV에서는 3.38 ~ 3.56 MeV로 분석되었다. Flux는 6 MV에서 $1.64{\times}10^{-5}{\sim}1.80{\times}10^{-5}{\sharp}/cm^2/e$, 15 MV는 $1.76{\times}10^{-4}{\sim}1.85{\times}10^{-4}{\sharp}/cm^2/e$로 계산되었다. 결과를 분석하면, 타깃 재질이 고원자번호일수록 평균에너지와 Flux가 증가하는 것으로 평가다. 본 연구를 바탕으로 광자의 물리적 특성에 대한 기초적인 자료를 제시할 수 있었으며, 추후 타깃 선정 시 경제성, 효율성은 물론 물리적 측면을 고려할 수 있어 적절한 선택을 할 수 있을 것으로 판단된다.

This study purpose is propose the basic data for selecting the optimal target material by analyzing the photon characteristics of various materials which was located in the head of medical linear accelerator. In this study, energy spectrum of 6, 15 MV photon beams were compared and analyzed for 13 target materials using MCNPX of Monte Carlo method. The mean energy for the 6 MV energy spectrum was 1.69 ~ 1.84 MeV and that for the 15 MV was 3.38 ~ 3.56 MeV, according to the target material. The flux for the 6 MV energy spectrum was $1.64{\times}10^{-5}{\sim}1.80{\times}10^{-5}{\sharp}/cm^2/e$ and that for the 15 MV was $1.76{\times}10^{-4}{\sim}1.85{\times}10^{-4}{\sharp}/cm^2/e$. The analysis shows that the average energy and flux increase with higher atomic number of the target material. Based on this study, it is possible to present the basic data about the physical characteristics of the photon, and it will be possible to select the target later considering economic, efficiency and physical aspect.

방사성동위원소를 이용한 아스팔트함량 측정장비의 실험적인 방법에 의한 설계는 많은 시간과 비용이 소요되므로, 코드모사를 통해 설계할 경우 이러한 노력을 줄일 수 있다. 본 연구에서는 장비의 활용성을 증대시키기 위해 법적 규제 면제치인 100 $\mu$Ci이하의 방사성동위원소를 이용하며, 6%의 아스팔트함량을 갖는 혼합물을 5분간 측정하였을 경우 0.2%이내의 함량측정오차를 갖는 장비를 MCNP 코드를 이용하여 설계하였다 또한 코드 모사를 통한 설계를 바탕으로 장비를 제작한 후 5개의 시료에 대한 함량을 측정하고 그 결과를 비교하여 코드의 적용가능성을 검증하였다 실험결과 6.03% 아스팔트 함량을 가진 시료를 5분간 측정하여 5.85%의 함량을 얻을 수 있었다.

Power density distribution and criticality of a pressurized water reactor are calculated with a Monte Carlo calculation using the MCNP code. The MCNP model is based on one-eighth core symmetry. Individual fuel assemblies are modeled with fullscope three dimensional description except grid spacer. The fuel rod is divided into eight axial segments. Core internals above and below the active fuel region is represented as coolant. After 400 cycle calculations, the system converges to a k value of 1.09151$\pm$0.00066. Fission reaction rate in each rod is also calculated to use as the source term in pressure vessel fluence calculation.

To validate the new Evaluated Nuclear Data File $(ENDF)/B-VIII.0{\beta}4$ library, 31 different critical cores were selected and used for a benchmark test of the important parameter keff. The four utilized libraries are processed using Nuclear Data Processing Code (NJOY2016). The results obtained with the $ENDF/B-VIII.0{\beta}4$ library were compared against those calculated with ENDF/B-VI.8, ENDF/B-VII.0, and ENDF/B-VII.1 libraries using the Monte Carlo N-Particle (MCNP(X)) code. All the MCNP(X) calculations of keff values with these four libraries were compared with the experimentally measured results, which are available in the International Critically Safety Benchmark Evaluation Project. The obtained results are discussed and analyzed in this paper.