Earticle

현재 위치 Home

기술

ICT 분야 전자 소자용 기술 개발을 위한 고무 기판에 코팅된 카본나노튜브의 특성 연구
Study on the characteristics of carbon nanotubes coated on rubber substrates for the development of electronic devices in the ICT field

첫 페이지 보기
  • 발행기관
    대한산업경영학회 바로가기
  • 간행물
    산업융합연구(구 대한산업경영학회지) KCI 등재 바로가기
  • 통권
    제23권 제1호 (2025.01)바로가기
  • 페이지
    pp.71-78
  • 저자
    김무진
  • 언어
    한국어(KOR)
  • URL
    https://www.earticle.net/Article/A461334

※ 기관로그인 시 무료 이용이 가능합니다.

4,000원

원문정보

초록

영어
 In this study, carbon nanotubes (CNTs) were coated on three different flexible and stretchable rubber materials, and optical, electrical, and mechanical properties were analyzed. A novel method of coating a solution-based CNT material on the rubber surface using a finger-worn rubber was performed. And then a CNT-based thin film was formed through subsequent heat treatment. Samples were produced by repeating the coating process two times on each rubber. The surface roughness of the rubbers decreased through the CNT coating. The light-responsive characteristics (reflectivity, transmittance, and absorbance) of the three different rubbers were measured and analyzed. The phenomenon of reflectance, transmittance, and absorbance alternately increasing and decreasing above 1,100 nm was observed in all samples. It was confirmed that there was no difference in surface resistance before and after repeated bending of a CNT thin film formed on a rubber substrate up to a bending radius of curvature of 0.2 mm for 200,000 cycles. However, in the evaluation of stretchable properties, when stretched to approximately 1.5 times its original length, the CNT network was disrupted, and resistance could no longer be measured. This remains a challenge to be addressed in the future.
한국어
본 연구에서는 플렉서블 및 스트레처블 가능한 3가지 서로 다른 고무소재들 상에 탄소나노튜브(CNT)를 코팅하여 광 학 및 전기적, 기계적인 특성을 분석하였다. 고무상에 용액 기반의 CNT 물질을 손가락에 낀 고무를 이용한 신개념의 방법으 로 용액을 전면에 코팅하고, 후속 열처리를 통해 CNT 기반의 박막을 형성하였으며, 이와 같은 방법으로 각 고무상에 총 2번 의 코팅 공정을 반복하여 샘플들을 제작하였다. CNT 코팅을 통해 고무들의 거칠기가 감소하는 경향을 확인하였다. 3가지 서 로 다른 고무에 대해 빛과의 반응 특성(반사도와 투과도, 흡수도)를 측정 및 분석하였으며, 반사도, 투과도, 흡수도 모두 1,100nm 이상에서 증가와 감소를 반복하는 현상이 모든 샘플에서 관찰되었다. 고무상에 형성된 CNT 박막의 벤딩에 따른 전기적인 특성 변화를 곡률반경 0.2mm까지 반복적으로 200,000번 벤딩 진행 전후 표면 저항 값에 차이가 없음을 확인하였 다. 하지만, 스트레처블 특성 평가에서는 원래 길이의 약 1.5배 이상으로 늘어났을 때 CNT의 연결고리들이 끊어져 저항값이 측정되지 않았으며, 향후 해결해야 할 과제가 될 것이다.

목차

요약 
Abstract
1. 서론
2. 선행연구
3. 연구방법 및 결과
3.1 고무상에 탄소나노튜브 코팅
3.2 고무상에 형성된 탄소나노튜브의 표면 형상
3.3 고무상에 형성된 CNT막의 광학적인 특성 분석
3.4 고무상에 형성된 CNT막의 전기적인 물성 및 스트레칭, 벤딩 특성 분석
4. 결론
REFERENCES

키워드

고무 탄소나노튜브 거칠기 반사도 및 투과도 벤딩 특성 스트레처블 평가 Rubber Carbon nanotube Roughness Reflectivity and transmittance Bending properties Stretchable evaluation

저자

  • 김무진 [ Moojin Kim | 강남대학교 전자공학전공 교수 ] Corresponding Author

참고문헌

자료제공 : 네이버학술정보

간행물 정보

발행기관

  • 발행기관명
    대한산업경영학회 [Dae Han Society of Industrial Management]
  • 설립연도
    2003
  • 분야
    복합학>과학기술학
  • 소개
    본 학회는 산업체·학계·연구소 등의 회원 상호간에 정보교환 및 지원을 통하여 산업경영에 관한 학문발전을 도모하고 산학에 관한 긴밀한 네트워크를 형성하여 기업의 경쟁력을 강화시키는데 그 설립 목적을 두고 있다.

간행물

  • 간행물명
    산업융합연구(구 대한산업경영학회지) [Journal of Industrial Convergence]
  • 간기
    월간
  • pISSN
    2635-8875
  • 수록기간
    2003~2026
  • 등재여부
    KCI 등재
  • 십진분류
    KDC 323 DDC 338

이 권호 내 다른 논문 / 산업융합연구(구 대한산업경영학회지) 제23권 제1호

    피인용수 : 0(자료제공 : 네이버학술정보)

    함께 이용한 논문 이 논문을 다운로드한 분들이 이용한 다른 논문입니다.

      페이지 저장