Earticle

The objective of the present study is to investigate thermal diffusion and radiation effects on unsteady MHD flow past a linearly accelerated vertical porous plate with variable temperature and also with variable mass diffusion in presence of heat source or sink under the influence of applied transverse magnetic field. The fluid considered here is a gray, absorbing/emitting radiation but a non-scattering medium. At time t > 0, the plate is linearly accelerated with a velocity $u=u_0t$ in its own plane. And at the same time, plate temperature and concentration levels near the plate raised linearly with time t. The dimensionless governing equations involved in the present analysis are solved using the closed analytical method. The velocity, temperature, concentration, skin-friction, the rate or heat transfer and the rate of mass transfer are studied through graphs in terms of different physical parameters like magnetic field parameter (M), radiation parameter (R), Schmidt parameter (Sc), Soret number (So), Heat source parameter (S), Prandtl number (Pr), thermal Grashof number (Gr), mass Grashof number (Gm) and time (t).

Thermal Diffusion Process(TD Process)을 통하여 베어링강 소재인 SUJ2 표면에 Vanadium Carbide를 석출시켜 표면 물성에 관한 연구를 진항하였다. $900{\sim}950^{\circ}C$ 온도와 2~6H 공정시간에 따라 TD Process에 의한 코팅층의 변화를 Micro Vikers Hardness Tester와 광학현미경, SEM, EDS를 통하여 관찰하였다. 그 결과 공정시간 및 온도는 코팅층 성장과 비례한다는 것을 확인 할 수 있었고 SUJ2 표면에 성장된 코팅층은 높은 경도값을 갖는 VC, CrC 코팅층임을 확인하였다.

We propose and demonstrate a fabrication method of chirped fiber gratings by a thermal diffusion process. The method could suggest a direction for a simple and cost-effective implementation of chirped fiber grating-based devices.

Expanded graphite (EG)/Ag nanoparticle composites were synthesized by the chemical reduction of Ag ions, followed by the addition of expanded graphite into an Ag reducing solution. The prepared composites showed uniform dispersion of Ag nanoparticles on the surface of expanded graphite and exhibited relatively higher thermal conductivities than those of pure expanded graphite. In the case of 10% Ag content in the composite, the thermal conductivity in the thickness direction was 78% higher than the pure expanded graphite. We suggest that EG/Ag nanoparticle composites are a strong candidate for advanced heat spreading material.

We examined the steady state solution for a strongly exothermic mixtures in some class A geometries subjected to different boundary conditions under Arrhenius, Bimolecular and Sensitised reactions. The solution of the governing nonlinear reaction diffusion equation was obtained using the variational method formulation executed in Mathematica package. The paper elucidates the influence of geometry, boundary conditions and types of reaction on the thermal ignition of the reactive mixture. Apart from validating known results in literature, the solution gave further insight into the influence of material properties and conditions on the occurrence of thermal ignition.

This paper presents a 3-dimensional diffusion simulation with adaptive solution strategy. The developed diffusion simulator VLSIDIF-3 was designed to re-refine areas. Refine scheme was calculated by the difference of doping concentration between any of two nodes. Each element is greater than tolerance and redo diffusion process until error is tolerable. Numerical experiment in low doping diffusion problem showed that this adaptive solution strategy is very efficient in both memory and time, and expected this scheme would be more powerful in complex diffusion model.

This study sought to determine the changes in weather conditions in urban streets, along with conditions of traffic and roads in urban areas. The variations in weather conditions depending on traffic differed according to distance. First, the temperature difference measured by traffic results is as follows: T1 point $1.03^{\circ}C$, T2 point $1.04^{\circ}C$, T3 point $0.9^{\circ}C$, T4 point $1.01^{\circ}C$, and T5 point $0.31^{\circ}C$. The average difference between the measured temperatures by the point of measurement was $0.86^{\circ}C$. The changes in wind velocity according to traffic volume results of the measurements is T1 point 1.32 m/s, T2 point 0.80 m/s, T3 point 0.29 m/s, T4 point 0.04 m/s, and T5 point 0.09 m/s. The difference between the average wind speeds was 0.51 m/s and traffic jams caused substantial differences in distance. The relative humidity tended to be inversely proportional to temperature. The measurements results ares T1 point 2.29%, T2 point 2.67%, T3 point 2.47%, T4 point 2.16%, and T5 point 0.91% The difference between the average relative humidity was 7.3%. In case of independent sampling T test according to traffic volume, changes in wind velocity and temperature were directly proportional to the level of statistical significance(p<0.01). On the other hand, relative humidity tended to be inversely proportional; however, there was no statistical significance.

정보의 수요가 점차 늘어감에 따라 필연적으로 고용량 저장 매체의 필요성이 점점 증대되고 있다. 현재 많이 사용되고 있는 하드디스크도 이미 저장 용량이 100Gb에 달하는 제품들이 상용화되었고 CD나 DVD등의 광기록매체의 저장 용량도 기존의 640Mb에서 700Mb(CD), 4.3Gb 또는 15～20Gb(DVD)로 점차 늘어나고 있다. 특히 광기록매체의 경우에는 하드디스크에 비하여 개체의 탈착 및 휴대가 간편하다는 점 등으로 인하여 차세대 저장 매체로 각광 받고 있으며 이 중 기록과 재생이 자유로운 Rewritable Disk는 일본을 중심으로 고속화, 고밀도화에 관한 연구가 활발히 진행되고 있다. (중략)

In this study, a simulation using Company A's COMSOL heat flow program was used to analyze the thermal diffusion simulation according to the depth of the high-temperature exposed cement paste. As a result of the analysis, it showed a similar relationship with the measured temperature as of 180 minutes.

Geopolymer는 시멘트와 비교하여 $CO_2$ 배출량의 감소, 내화성, 낮은 열전도성 등 다양한 장점을 보유하고 있는 eco-friendly 건설재료이다. 그러나 표면에 화염을 가할 경우 geopolymer panel 표면의 열적거동에 대한 연구결과는 많지 않다. 본 연구에서는 내열성 건축자재로서 화염노출시 geopolymer 경화체의 표면특성을 조사하기 위하여 alumina 골재가 사용된 geopolymer 경화체 표면의 화염노출 특성에 대하여 조사하였다. 화염노출시 panel의 외형변형 및 열충격에 의한 크랙은 없었으며, calcite의 잔존량과 aluminosilicate gel의 halo 패턴으로 보아 화염에 의한 탈탄산 및 탈수는 표면에 국한되어 발생했으며, geopolymer 경화체의 내구성은 화염조사 후에도 유지되고 있는 것으로 판단된다. Quartz와 calcite가 감소함에 따라 gehlenite와 calcium silicate가 증가하는 경향을 나타내고 있으며, BFS의 치환량이 많을수록 현저하게 나타난다. 화염노출에 따른 미세구조의 변화는 탈탄산, 결정수의 탈수 등으로 기공의 형성과 발전되는 과정을 거쳐 calcium silicate, gehlenite 등과 같은 새로운 결정상의 형성에 의해 geopolymer panel 표면의 치밀화와 강화기구로 작용하여 내구성이 향상된 것으로 생각된다.

Geopolymer is an eco-friendly construction material that has various advantages such as reduced $CO_2$ emission, fire resistance and low thermal conductivity compared to cement. However, it has not been many studies on the thermal behavior of the surface of the geopolymer panel when flame is applied to the surface. In this study, surface characteristics of hardened geopolymer on flame exposure was investigated to observe its characteristics as heat-resistant architectural materials. External structure changes and crack due to the heat shock were not observed during the exposure on flame. According to the residue of calcite and halo pattern of aluminosilicate gel, decarboxylation and dehydration were extremely limited to the surface and, therefore, it is thought that durability of hardened geopolymer was sustained. Gehlenite and calcium silicate portion was inversely proportional to quartz and calcite and significantly directly proportional to BFS replacement ratio. Microstructure changes due to the thermal shock caused decarboxylation and dehydration of crystallization and it was developed the pore and new crystalline phase like calcium silicate and gehlenite. It is thought that those crystalline phase worked as a densification and strengthening mechanism on geopolymer panel surface.

The important drawback of hardware fasteners consisted of 304 stainless steel (STS) is a frequent galling caused by a combination of friction and adhesion between the sliding surface. To improve the anti-galling effect, Sn-Al coatings by a thermal diffusion have been developed. The thermal diffusion by pack cementation with an $AlCl_3$ activator at $250^{\circ}C$ for 1 hour produced an Sn-Al alloy coating layer with an average thickness of $9.9{\pm}0.5{\mu}m$ on the surface of 304 STS fasteners. Compared with the galling frequency of the 304 STS fasteners, Sn-Al coatings on the surface of 304 STS fasteners demonstrated about 2.8-time reduction of the galling frequency.

Modern industry has a wide variety of application areas such as ocean industry, construction and automobile industry. With the current circumstances, the need for anti-corrosion technology that can be used on materials to withstand in harsh environments, is increasing. In this study, we have sought to develop a metal coating technology with zinc and aluminum powders as a potential anti-corrosion material. To make a coating on metal products, a thermal diffusion coating method was used under the conditions of $350^{\circ}C$ for 30 minutes. Optical microscope, Field emission scanning electron microscope (FE-SEM&EDX) and X-ray diffraction analysis were used to analyze a coating layer. As a result, we have confirmed that the generated amount of rust on metal parts coated with thermal diffusion coating method decreased dramatically compared with non-coated metal parts. Furthermore, the anti-corrosion performance was evaluated according to the different ratio of zinc and aluminum. Finally, we confirmed the possibility of application and commercialization of our coating technique on metal parts used in harsh industrial based on the results of these performance.