Earticle

보는 하천수량을 확보하고 낙차공은 하상안정을 위한, 그리고 교량은 차량 등의 이동을 위한 하천횡단시설물이다. 그러한 시설물의 안정성을 확보하기 위하여 하천설계기준에서는 시설물의 최소 규모에 관한 지침을 제시하고 있으나 실태 조사 결 과에 의하면, 기존 보 및 낙차공의 물받이 및 바닥보호공의 규모는 설계기준을 만족시키지 못하는 경우가 대부분이고 교량 의 교각은 일부만 만족시키는 것으로 나타났다. 기존 보 및 낙차공의 수리적 안정성을 제고하기 위해서는 설계기준에서 제 시한 바닥보호공에 대한 물받이의 비율인 3.3을 최소값으로 확보해줄 필요가 있다. 표본하천 시설물 실태조사에 의하면 기 존 보 및 낙차공을 자연형 여울공으로 개량할 경우 적용하는 종단경사는 1:20이 가장 적정한 것으로 나타났다. 또한, 교량 의 철거 또는 재가설에 관한 결정에서 교각의 여유고 및 경간장 위배사항만 고려하고 있지만, 향후 교량 노후도 및 경간장 완화 규정 등을 종합적으로 검토하여 결정하는 것이 바람직하다. 본 연구에서는 설계기준, 하천실태 조사결과, 일본사례 등 을 통하여 기존 보, 낙차공 및 교각의 수리적 안정성을 제고하는 종합적인 방안을 제시하였다. 하천횡단시설물의 안정화 노 력은 정부 차원의 예산 지원과 적극적인 하천관리를 통하여 이룰 수 있으며, 이를 통하여 하천재해를 예방하고 건전한 하천 환경을 유지할 수 있을 것이다.

Weirs are to secure amount water of streams and drop structures are to enhance stabilization of stream bed and bridges are to connect isolated region, which are called stream crossing structures. In the stream design criteria, directions for minimum size of structures are suggested to secure stability of stream crossing structures. However the sizes of almost all existing weirs and drop structures are not satisfied with the stream design criteria and only 22 percent of the peirs of bridges are satisfied. To enhance hydraulic stability of existing weirs and drop structures, it is required that the ratio of bed protection to apron should be above 3.3. According to factual survey of structures in the sample streams, it has been shown that the longitudinal slope of rapid works with 1:20 is the most reasonable to design velocity if existing weirs and drop structures are rehabilitated into rapid works. It has been known that violating freeboard and span length of piers should make existing bridges reconstructed or removed. However, comprehensive review including deterioration level of bridges, special regulation for span length, etc. should be considered to determine rehabilitation plan of bridges. In this study, a procedure has been suggested to improve hydraulic stability of weirs, drop structures and piers of bridges. Sound environment of stream and reduction of natural disaster could be achieved by improving stability of cross structures, which could be obtained by governmental budget and active stream management including observance of design criteria.

This paper deals with flow characteristics on the air entrainment and the energy dissipation in nappe flow over the stepped drop structure. Nappe flow occurred at low flow rates and for relatively large step height Dominant flow features include an air pocket, a free-falling nappe impact and a subsequent hydraulic jump on the downstream step. Air entrainment occurred from the step edge, through a free-falling nappe impact and a hydraulic jump. Most energy was dissipated by nappe impact and in the downstream hydraulic jump. It was related with the step height and the overflow depth, but not related with step slope. The stepped drop structure was found to be effcient for water treatment and energy dissipation associated with substantial air entrainment.

This paper deals with oxygen transfer by air entrainment and energy dissipations by flow characteristics at the stepped drop structure. Nappe flow occurred at low flow rates and for relatively large step height. Dominant flow features included an air pocket, a free-falling nappe impact and a subsequent hydraulic jump on the downstream step. Most energy was dissipated by nappe impact and in the downstream hydraulic jump. Skimming flow occurred at larger flow rates with formation of recirculating vortices between the main flow and the step comers. Oxygen transfer was found to be proportional to the flow velocity, the flow discharge, and the Froude number. It was more related to the flow discharge than to the Froude number. Energy dissipations in both cases of nappe flow and skimming flow were proportional to the step height and were inversely proportional to the overflow depth, and were not proportional to the step slope. The stepped drop structure was found to be efficient for water treatment associated with substantial air entrainment and for energy dissipation.

We demonstrate a linear bus wavelength-reused gigabit wavelength-division multiplexing passive optical network (WDM-PON) with multiple optical add-drop nodes. A commercially available reflective semiconductor optical amplifier-based WDM-PON has a sufficient power budget to provide multiple optical add/drop nodes in 16 WDM channels. Sixteen 1.25 Gb/s WDM channels are successfully transmitted over 20 km of single-mode fiber with four optical add/drop multiplexers, even with 32 dB reflection and chromatic dispersion in the link.

The goal of this paper is to examine how Case Drop (the drop of the case markers) correlates with the prosodic structure in Korean. On the assumption that intervocalic Lenis Stop Voicing (LSV) applies within the domain of the Accentual Phrase (AP), voicing analyses are performed on intervocalic lenis stop consonants before and after Case Drop. A statistical analysis reveals that the drop of the nominative and accusative case markers significantly alter the AP structure. Pitch values will then be extracted to verify that such changes in the AP structure conform to the pitch properties proposed for the AP (Jun 1993, 1998). The results show that the AP structure suggested by LSV does not always coincide with that imposed by the pitch properties.

The paper concentrates on an experimental study of the pressure drop in double-layered packed beds formed by glass spheres, having the configuration of horizontal and vertical stratification. Both single-phase and two-phase flow tests are performed. The pressure drop during the test is recorded and the measured data are compared with those of homogeneous beds consisting of mono-size particles. The results show that for the horizontally stratified bed with fine particles atop coarse particles, the pressure drop in top layer is found higher than those of homogenous bed consisting of the same smaller size particles, while the measured pressure drop of bottom part is similar with those of similar homogenous bed. But for the homologous bed with upside-down structure, the stratification has little or no effect on the pressure drop of the horizontally stratified bed, and the pressure drop of each layer is almost same as that of homogeneous bed packed with corresponding spheres. Additionally, in vertically stratified bed, the pressure drops on the left and right side is almost equal and between those in homogeneous beds. It is speculated that vertically stratified structure may lead to lateral flow which redistributes the flow rate in different parts of packed bed.

In this research, the surface roughness affecting the pressure drop in a pipe used as the steam generator of a PWR was studied. Based on the CFD (Computational Fluid Dynamics) technique using a commercial code named ANSYS-FLUENT, a straight pipe was modeled to obtain the Darcy frictional coefficient, changed with a range of various surface roughness ratios as well as Reynolds numbers. The result is validated by the comparison with a Moody chart to set the appropriate size of grids at the wall for the correct consideration of surface roughness. The pressure drop in a full-scale U-shaped pipe is measured with the same code, correlated with the surface roughness ratio. In the next stage, we studied a reduced scale model of a U-shaped heat pipe with experiment and analysis of the investigation into fluid-structure interaction (FSI). The material of the pipe was cut from the real heat pipe of a material named Inconel 690 alloy, now used in steam generators. The accelerations at the fixed stations on the outer surface of the pipe model are measured in the series of time history, and Fourier transformed to the frequency domain. The natural frequency of three leading modes were traced from the FFT data, and compared with the result of a numerical analysis for unsteady, incompressible flow. The corresponding mode shapes and maximum displacement are obtained numerically from the FSI simulation with the coupling of the commercial codes, ANSYS-FLUENT and TRANSIENT_STRUCTURAL. The primary frequencies for the model system consist of three parts: structural vibration, BPF(blade pass frequency) of pump, and fluid-structure interaction.

This paper presents a computational framework for drop time assessment of a control element assembly (CEA) under fuel assembly (FA) deformations. The proposed framework consists of three key components: 1) finite element modeling of CEA, 2) fluid-structure interaction to compute drag force, and 3) modeling of frictional contact between CEA and FA. Specially, to accommodate the large motion of CEA, beam elements based on absolute nodal coordinate formulation (ANCF) are adopted. The continuity equation is utilized to calculate the drag force, considering flow changes in the cross-sectional area during the CEA drop. Lastly, beam-inside-beam frictional contact model is employed to capture practical contact conditions between CEA and FA. The proposed framework is validated through experiments under two scenarios: free falls of CEA within FA, encompassing undeformed and deformed scenarios. The experimental validation of the framework demonstrated that the drop time of CEA can be accurately predicted under the complex coupling effects of fluid and frictional contact. The drop times of the S-shaped deformation case is longer than those of the C-shaped deformation case, affirming the time delay due to frictional force. The validation confirms the potential applicability to access the safety and reliability of nuclear power plants under extreme conditions.

하천의 흐름을 파악하기 위해서는 일반적으로 수치모형 해석을 이용한다. 흐름특성을 파악하기 위해서는 수리모형 실험을 통하여 결과를 분석하는 것이 이상적이나 비용과 시간이 많이 소요되는 어려움이 있다. 이러한 이유로 원형에 대해 모형 법칙을 적용하여 정확하고 신뢰할 수 있는 결과 값을 도출하기 위해 수리모형 실험을 수행한다. 만곡부 흐름은 원심력의 영향을 받아 외측으로 향하는 2차류가 발생하고, 외측의 수위가 내측의 수위보다 높아져 횡방향으로 수면경사 상승이 발생한다. 이런 현상 때문에 1차원 수치모형을 적용하는 경우 제방의 안정성 문제가 발생하게 된다. 본 논문에서는 경기도 의정부에 있는 백석천 만곡부 경사형 낙차공의 흐름특성을 수리모형 실험 결과 값과 1, 2차원의 수치모형 해석 결과 값을 비교하였다. 100년 빈도 설계홍수량에 대해 비교해 본 결과 수리모형 실험과 수치모형 해석의 결과 값은 지점에 따라서 5~10%의 유속 및 수심이 상이하게 나타났다. 불균등한 유속분포에 의해 세굴과 퇴적현상이 예상되는 경우에는 수치모형 해석의 결과 값을 수정하여 적용할 필요성이 있으며 본 논문에서는 이러한 보정에 필요한 값을 제시하였다. 1, 2차원이 아닌 3차원 수치모형 해석을 추가적으로 비교분석한다면 유효한 결과를 얻을 수 있을 것으로 기대된다.

본 연구에서는 완경사 계단형 낙차공에서 하류수심 변화에 따른 도수 형태의 변화와 WTF 흐름 특성에 대한 분석을 수행하였다. 일정한 유량에서 하류수위를 증가시키면 도수 형태가 달라지는데 특히 계단 끝단에서 완전도수, 잠김도수(B점프), downward curved jet, upward curved jet, wave type flow(WTF)가 차례로 나타났다. 잠김도수에서는 표면 롤러 현상이 관찰되었고 curved jet에서는 큰 유속 감세 없이 파가 하류까지 전달되었다. WTF에서는 사류흐름이 바닥 recirculation 구역의 영향으로 변형되면서 wave 형태의 도수를 발생시켰다. 하류수위를 점점 증가 시키면 도수의 발생 위치가 계단 위쪽으로 이동하며 잠김도수와 WTF가 번갈아가며 발생하였다. 하류수위가 높아질수록 도수의 규모는 작아졌으며 표면 롤러도 미약해지는 경향을 보였다. 세 가지 유량조건에 따른 WTF의 규모를 비교한 결과 유량이 증가할수록 WTF의 크기가 증가하였으며 무차원화한 WTF의 형상은 거의 비슷한 것으로 나타났다. 계단형 낙차공은 기존낙차공에서 발생하는 도수와 달리 WTF가 발생되므로 이에 대한 분석이 필요하다. WTF가 발생하는 구간의 수위는 하류수위보다 높아지기 때문에 하천 설계 시 하천 접합부의 조건(구수부지설치, 제방설치 등)에 따라 wave의 높이가 설계의 중요 인자로 고려되어야 할 것이다. WTF는 지금까지의 계단형 낙차공 설계 시 고려되지 못한 부분으로서 차후에 계단형 구조물 또는 계단식 변형 구조물 설계 시 주요 자료로 활용 될 것이다.

난류흐름 거동은 지형이나 수공구조물과 같은 고체 경계면의 변화에 민감하게 반응하며 특징 또한 다양하다. 보나 여수로 등과 같은 단차 구조물을 통과하는 흐름은 구조물의 모서리 같은 흐름 경계면이 급변하는 지점에서는 흐름분리(flow separation)가 발생하는 것이 특징이다. 이러한 흐름분리로 인해 전단층이 발생하며 흐름 재순환(recirculation)이 구조물 하류부에 형성된다. 이 연구에서는 낙차공 형식의 단차 구조물 하류부에서의 흐름 거동을 이해하기 위해 CFD모델링을 통하여 계산된 3차원 유동장을 분석한다. 난류 모의는 하이브리드 LES(large-eddy simulation)/RANS 계산 기법인 IDDES(improved delayed detached-eddy simulation)기법을 적용한다. IDDES의 기본 모형으로는 k-ω SST모형과 Spalart-Allmaras모형을 이용하여 두 모형의 성능을 평가한다. 자유수면의 변동은 VoF(volume of fluid)기법을 이용하여 계산하며, 각 지배방정식은 최소의 수치분산을 유지하면서 수치해의 안정성을 확보할 수 있는 2차 정확도의 유한체적법을 이용하여 이산화하였다. 수치해석 결과는 레이놀즈수 23,400과 후르드수 0.22의 조건에서 기존에 계측된 자료와 비교하여 수치모형의 정확도를 평가하고 하상 단차 하류부에서의 흐름 거동 특성을 분석한다. 계산 결과는 공학적으로 널리 사용되는 RANS 수치모의에서 볼 수 없는 전단층과 난류구조의 동적 거동 특성과 이에 따른 레이놀즈 응력분포의 특성을 설명해준다.

대표적인 하천횡단구조물 중 하나인 낙차공은 하천하상의 안정을 목적으로 설치되지만 이는 하천환경의 연속성을 차단하고, 수생태환경의 파괴를 야기하는 것으로 알려져 있다. 따라서 본 연구에서는 생태통로로서의 기능을 갖는 저낙차 자연형 낙차공을 모형으로 제작하여 실험실 실험을 수행하고, 적절한 지배인자 사이의 관계를 도출하여 국부세굴공 규모의 예측식을 제안하였다. 직선형과 6가지 상향 V 자형의 낙차공 모형에 대하여 각각 실험유량은 4가지로 총 28개의 조건에 대해서 실험을 수행하였다. 각각의 실험조건별 세굴실험 결과를 바탕으로 기존에 제안된 세굴심 추정식을 적용한 결과보다 최대세굴심이 다소 크게 발생함을 확인하였다. 따라서 낙차공 직하류부에서 발생하는 세굴공 발생 주요인자들 사이의 상관관계를 분석한 결과, 낙차공으로의 유입흐름 특성과 낙차공의 높이, 낙차공의 총횡단길이와의 상관관계가 높게 나타남을 확인하였다. 또한 이를 토대로 각 실험조건별 세굴심과 세굴길이에 상관관계가 높다고 판단되는 변수들을 무차원화하여 최대세굴공의 깊이와 길이 산정식을 각각 제안하였다. 향후 추가적으로 다양한 하상토 재료와 수심변화를 고려한 실험적 연구 및 수치해석 연구를 병행하여 보다 정확한 세굴심 산정식을 도출할 수 있다.

A drop structure, one of the representative river-crossing structures, is constructed to stabilize a riverbed. On the other hand, the structure interrupts the continuity of the river and causes the destruction of the hydro-ecological environment. Therefore, laboratory experiments of a natural type of drop structure with low differences were performed, and the empirical formula of a local scour hole is proposed. Four experimental flow rates were tested for various types of the drop structure models with 28 test cases. Based on the scour test, it was confirmed that the maximum scour depth occurs rather than the result of applying the previously proposed scour depth formulae. Correlation analysis of the major factors of scour hole at the downstream of the drop structure revealed a strong correlation between the upstream flow characteristics, drop structure height, and total crossing length of the drop model. In addition, the depth and length estimation formula of the maximum scour hole were proposed using the dimensionless variables and validated. In the future, it is also expected that more accurate scour prediction and calculation can be derived by conducting experimental studies and numerical analysis considering the various bed materials and flow conditions.

Experimental studies were performed to determine the characteristics of flow structure and pressure drop in 15 : 1 scale models of multi-louvered fin heat exchanger in a wide range of variables($L_P/F_P=0.5{\sim}1.23$, ${\theta}=27^{\circ}{\sim}37^{\circ}$, $Re_{LP}=50{\sim}2000$). Flow structure inside the louvered fin was analyzed by smoketube method and new correlations on flow efficiency and drag coefficient were suggested. The new definition for flow efficiency, which modifies the existing flow efficiency, can predict the flow efficiency in the range above mentioned and is represented as a function of Reynolds number, louver pitch to fin pitch ratio, louver angle at low Reynolds number. Drag coefficient which is defined here is a function of Reynolds number, louver pitch to fin pitch ratio, louver angle below critical Reynolds number, and can be represented by a function of louver pitch to fin pitch ratio only above the critical Reynolds number.

다이어프램 방식 준비작동식 유수검지장치의 압력손실을 줄이기 위하여 본체 구조를 개선하였다. 개정된 유수제어밸브의 압력손실시험 기술기준을 통과하기 위해서는 압력손실이 20.7 kPa을 초과하여서는 안된다. 압력손실시험은 한국소방산업기술원 유수제어밸브 기술기준에 따라서 실시하였다. 준비작동식 유수검지장치는 습식 유수검지장치에 비해 압력손실이 크게 발생하였는데, 그 원인을 유체의 유동현상과 관련하여 분석하였다. 준비작동식 유수검지장치의 본체 내부 구조는 유로의 단면 크기와 방향 변화로 인해 압력손실 요인이 많았다. 이러한 압력손실 요소를 제거하기 위해 습식 유수검지장치와 비슷한 클래퍼 타입으로 구조를 변경하였다. 구조 변경 후 압력손실 값은 호칭 80A인 경우 80.9 kPa에서 14.4 kPa로 감소하였으며, 호칭 100A인 경우 171.0 kPa에서 14.2 kPa로 감소하여 기술기준에 적합한 압력손실 값을 얻을 수 있었다.

The body structure of diaphragm type preaction valve was improved in order to reduce the pressure drop. The pressure drop must be kept within 20.7 kPa to pass the revised (2012. 2. 9) standard for alarm valve and preaction valve. The pressure drop test was carried out by KFI (Korea Fire Institute) standard. The pressure drop of a preaction valve was higher than that of an alarm valve. Causes for increasing the pressure drop were investigated with the fluid flow in the valve. The preaction valve had more pressure drop factors (changes in velocity and direction) compared with the alarm valve. Inner structure of the preaction valve was changed to the clapper type to remove the pressure drop factors. In 80A and 100A size of preaction valves, the pressure drop was reduced from 80.9 and 171.0 kPa to 14.4 and 14.2 kPa respectively, after the change of the structure.

It is known that damages to the subsea cables used for electric power transmission between islands and countries, including renewable energy from offshore wind power, current, tides, etc., cost much to restore, which causes social and economic losses. Various types of fishing rigs and anchors have been reported to be the greatest hazards to subsea cables. It is possible to design and construct a suitable protection facility for a subsea cable by precisely estimating the underwater behavior of such hazardous apparatuses. In this study, numerical simulations of the underwater behaviors of various hazardous apparatuses were carried out using fluid-structure interaction (FSI) analysis as a basic study to simulate the actual behavior phenomena of hazardous apparatuses in relation to a subsea cable. In addition, the underwater drop characteristics according to the types of hazardous apparatuses were compared. In order to verify the accuracy of the FSI analysis method used in this study, we compared the test results for underwater drops of a steel ball bearing. Stock anchors, stockless anchors, and rocket piles, which were actually reported to be the cases of damage to subsea cables along the southwest coast of Korea, were considered as the hazardous apparatuses for the numerical simulations. Each hazardous apparatus was generated by a Lagrangian model and coupled with the fluid domain idealized by the Eulerian equation to construct the three-dimensional FSI analysis model. The accuracy of the numerical simulation results was verified by comparing them with the analytical solutions, and the underwater drop characteristics according to the types of hazard apparatuses were compared.

In this paper, the pressure drops were investigated according to the sintered porous wick structure in loop heat pipe(LHP) by theoretical analysis. LHP has the wick only in evaporator for the circulation of working fluid, so utilizes porous wick structure which pore diameter is very small for large capillary force. This paper investigates the effects of different parameters on the pressure drops of the LHP such as particle diameter of sintered porous wick, wick porosity, vapor line diameter, thickness of wick and heating capacity. Working fluid is water and the material of sintered porous wick is copper. According to the these different parameters, capillary pressure, pressure drop in wick were analized by theoretical design method of LHP.

본 연구는 IGBT 구조에서 JFET 영역의 드라이브 인 확산거리 및 JFET영역의 윈도우의 크기에 따라서 항복전압과 온상태 전압강하 특성을 분석하였다. 시간은 동일하게 하면서 온도를 상승시켜 확산거리를 조정하였으며, 그 결과 항복전압은 감소되나, 온 상태 전압 강하 특성은 현저하게 좋아지는 것을 알 수 있었다. 따라서 드리프트 층의 비저항을 변화시켜 항복전압을 1440V로 고정하여 1.15V의 낮은 온 상태 전압 강하 값을 얻을 수 있었다. 따라서 본 연구결과를 토대로 Planar Gate IGBT에서는 JFET 영역의 공정 및 설계 파라미터를 효율적으로 조절한다면 같은 항복전압을 기준으로 상당히 낮은 온 상태 전압 강하 값을 확보할 수 있어, 소비전력의 측면에서 충분히 활용할 수 있을 것으로 판단된다.

Power semiconductors are semiconductors capable of controlling power over 1W and are mainly used as switches. This power semiconductor device has been developed with the goal of reducing power consumption and high breakdown voltage. This research was analyzed electrical characteristics of IGBT(Insulated Gate Biopolar Transistor) according to diffusion length of JFET region. The Diffusion length of JFET region was controlled by temperature and time using T-CAD simulator. As a result of experiments, we could obtain 1.14V low on state voltage drop by fixing 1440V breakdown voltage.