Earticle

공극의 유무에 따라 건조한 시편에서 전기비저항의 온도 및 습도의 영향을 고찰하였다. 공극이 있는 사암(SS) 및 대리암(MB)과 공극이 없는 강화유리(TG)의 3종의 시편에 대하여, 환경시험기의 설정 온도를 15, 25, 35℃, 습도를 45, 65, 85%, 그리고 시편의 초기조건을 건조상태와 습윤상태로 달리하여 총 54 경우에 대하여 전압송신-전류측정법에 의해 전기비저항을 모니터링하였다. 초기조건을 달리하여 10 시간 동안 측정한 두 전기 비저항 그래프로부터 두 경우가 모두 같은 전기비저항으로 수렴한다는 조건으로 점근식을 적용하면 특정 온도와 습도에서의 전기비저항을 유일하게 제시할 수 있다. 또한, TG는 습도보다는 온도에 SS와 MB는 온도보다는 습도에 더 강하게 영향을 받는다. 즉, SS와 MB는 비록 0.42%와 0.74%로 공극률이 매우 작음에도 불구하고 공극의 존재에 의해 측정되는 전기비저항이 온･습도변화에 크게 영향을 받는다.

Temperature and humidity dependency on electrical resistivity are discussed using sandstone (SS) and marble (MB) for porous samples and tempered glass (TG) for nonporous sample. A total of 54 experiments has been performed; 3 samples, 3 temperature conditions of 15, 25, and 35℃, 3 relative humidity conditions of 45, 65, and 85%, and 2 different initial conditions of dry and wet. Resistivity changes have been monitored for 10 hours by a voltmeter-ammeter method. Asymptote equation is successfully applied to the resistivity change for both dry and wet initial conditions simultaneously, which allow us to determine unique resistivity on a specific temperature and relative humidity. For TG sample, stronger resistivity changes can be observed by temperature change rather than relative humidity change, while vise versa for porous SS and MB samples, which means that even very small porosity of 0.42% and 0.74%, respectively, affects the resistivity with temperature and relative humidity changes.

최근 평판 디스플레이 산업의 발전에 따라 능동행렬 액정 표시 소자 (AMOLED : Active Matrix Organic Liquid Crystral Display) 가 차세대 디스플레이 분야에서 각광을 받고있다. 기존의 TFT-LCD에 사용되는 a-Si:H는 균일도가 좋지만 전기적인 스트레스에 의해 쉽게 열화되고 낮은 이동도는 갖는 단점이 있으며, ELA (Eximer Laser Annealing) 결정화 poly-Si은 전기적인 특성은 좋지만 uniformity가 떨어지는 단점을 가지고 있어서 AMOLED 및 대면적 디스플레이에 적용하기 어렵다. 따라서 a-Si:H TFT보다 좋은 전기적인 특성을 보이며 ELA 결정화 poly-Si TFT보다 좋은 uniformity를 갖는 SPC (Solid Phase Crystallization) poly-Si TFT가 주목을 받고있다. 본 연구에서는 차세대 디스플레이 적용을 위해서 glass 기판위에 증착된 a-Si을 SPC 로 결정화 시킨 후 TFT를 제작하고 평가하였다. 또한 TFT 형성시에 저온공정을 실현하기 위해서 소스/드레인 영역에 실리사이드를 형성시켰다. 소자 제작시의 최고온도는 $500^{\circ}C$ 이하에서 공정을 진행하는 저온 공정을 실현하였다. Glass 기판위에 a-Si이 80 nm 증착된 기판을 퍼니스에서 24시간 동안 N2 분위기로 약 $600^{\circ}C$ 에서 결정화를 진행하였다. 노광공정을 통하여 Active 영역을 형성시키고 E-beam evaporator를 이용하여 약 70 nm 의 Pt를 증착시킨 후, 소스와 드레인 영역의 실리사이드 형성은 N2 분위기에서 $450^{\circ}C$, $500^{\circ}C$, $550^{\circ}C$에서 열처리를 통하여 형성하였다. 게이트 절연막은 스퍼터링을 이용하여 SiO2를 약 15 nm 의 두께로 증착하였다. 게이트 전극의 형성을 위하여 E-beam evaporator 을 이용하여 약 150 nm 두께의 알루미늄을 증착하고 노광공정을 통하여 게이트 영역을 형성 후 에 $450^{\circ}C$, H2/N2 분위기에서 약 30분 동안 forming gas annealing (FGA)을 실시하였다. 제작된 소자는 실리사이드 형성 온도에 따라서 각각 다른 특성을 보였으며 $450^{\circ}C$에서 실리사이드를 형성시킨 소자는 on currnet와 SS (Subthreshold Swing)이 가장 낮은것을 확인하였다. $500^{\circ}C$와 $550^{\circ}C$에서 실리사이드를 형성시킨 소자는 거의 동일한 on current와 SS값을 나타냈다. 이로써 glass 기판위의 SB-TFT 제작 시 실리사이드 형성의 최적온도는 $500^{\circ}C$로 생각되어 진다. 위의 결과를 토대로 본 연구에서는 SPC 결정화 방법을 이용하여 SB-TFT를 성공적으로 제작 및 평가하였고, 차세대 디스플레이에 적용할 경우 우수한 특성이 기대된다.

Six metallic alloys, namely, Crofer22, ZMG232, an equivalent ZMG232, stainless steels SS430, SS304 and Inconel718 were investigated. A commercial Asahi Bulk Glass is sealed on these materials and evaluated for oxidation behavior under a hot air environment for various period of time and for thermal expansion. Then the resultant oxide scale was studied; with the microstructure and chemical composition of the crystalline phases investigated by scanning electron microscopy (SEM) and energy dispersive spectroscopic (EDS) analysis. The results show the Asahi bulk glass on ZMG232 was good for compaction and adhesion; no vacancies in the glass. ZMG232 seems to be more suitable for Asahi bulk glass than the other alloys. The glass does not fully crystallize even after long-term heat treatments at 500-600 oC. Sealing glass over a long period of time during operation of a solid oxide fuel cell (SOFC) would generate thermal stresses in the seal and may have adverse effects on its mechanical performance. This may lead to cracking of the seal, resulting in mixing of the fuel and the oxidant gases.

Port facilities and marine structures used in marine environment were encountered to corrosion damages because of the influence of $Cl^-$. Generally, to protect these accidents, mainly applied anti-corrosion paint and epoxy coating. But it was still remained erosion-corrosion damage such as impingement erosion, cavitation erosion, deposit attack. There was needs to develope the new coating materials to protective those corrosion damages. This paper, polyester glass flake, vinylester glass flake lining and epoxy coating for SS were investigated electrochemical tests and cavitation erosion test for corrosion behaviour under sea water. The main results obtained are as follows, 1) Surface of epoxy coating appear erosion pin hole but surface of polyester glass flake and vinylester glass flake lining do not appear erosion pin hole after impingement-cavitation erosion test in sea water. 2) Weight loss of polyester glass flake and vinylester glass flake lining do not occur after impingement-cavitation erosion test in sea water. 3) Corrosion current density of polyester glass flake lining less drained than epoxy coating and substrate under corrosion potential.. 4) Corrosion current density of vinylester glass flake lining with three coating less drained than that of polyester glass flake lining with two coating.

NiTiZrSiSn bulk metallic glass powder was produced using inert gas atomization and then was sprayed onto a SS 41 mild steel substrate using the kinetic spraying process. Through this study, the effects of thermal energy of in-flight particle and crystallization degree by powder preheating temperature were evaluated. The deformation behavior of bulk metallic glass is very interesting and it is largely dependent on the temperature. The crystalline phase formation at impact interface was dependent on the in-flight particle temperature. In addition, variations in the impact behavior need to be considered at high strain rate and in-flight particle temperature.

Objectives: The aim of this study was to evaluate the fluoride release of conventional glass ionomer cements (GICs) and resin-modified GICs. Materials and Methods: The cements were grouped as follows: G1 (Vidrion R, SS White), G2 (Vitro Fil, DFL), G3 (Vitro Molar, DFL), G4 (Bioglass R, Biodinamica), and G5 (Ketac Fil, 3M ESPE), as conventional GICs, and G6 (Vitremer, 3M ESPE), G7 (Vitro Fil LC, DFL), and G8 (Resiglass, Biodinamica) as resin-modified GICs. Six specimens (8.60 mm in diameter; 1.65 mm in thickness) of each material were prepared using a stainless steel mold. The specimens were immersed in a demineralizing solution (pH 4.3) for 6 hr and a remineralizing solution (pH 7.0) for 18 hr a day. The fluoride ions were measured for 15 days. Analysis of variance (ANOVA) and Tukey's test with 5% significance were applied. Results: The highest amounts of fluoride release were found during the first 24 hr for all cements, decreasing abruptly on day 2, and reaching gradually decreasing levels on day 7. Based on these results, the decreasing scale of fluoride release was as follows: G2 > G3 > G8 = G4 = G7 > G6 = G1 > G5 (p < 0.05). Conclusions: There were wide variations among the materials in terms of the cumulative amount of fluoride ion released, and the amount of fluoride release could not be attributed to the category of cement, that is, conventional GICs or resin-modified GICs.

At the Korea Institute of Radiological and Medical Sciences, physical human phantoms were developed to evaluate various radiation protection quantities, based on the mesh-type reference computational phantoms of the International Commission on Radiological Protection. The physical human phantoms were fabricated such that a radiophotoluminescent glass dosimeter (RPLGD) with a Tin filter, namely GD-352M, could be inserted into them. A Tin filter is used to eliminate the overestimated signals in low-energy photons below 100 keV. The measurement uncertainty of the RPLGD reader system based on GD-352M should be analyzed for obtaining reliable protection quantities before using it for practical applications. Generally, the measurement uncertainty of RPLGD systems without Tin filters is analyzed for quality assurance of radiotherapy units using a high-energy photon beam. However, in this study, the measurement uncertainty of GD-352M was analyzed for evaluating the protection quantities. The measurement uncertainty factors in the RPLGD include the reference irradiation, regression curve, reproducibility, uniformity, energy dependence, and angular dependence, as described by the International Organization for Standardization (ISO). These factors were calculated using the Guide to the Expression of Uncertainty in Measurement method, applying ISO/ASTM standards 51261(2013), 51707(2015), and SS-ISO 22127(2019). The measurement uncertainties of the RPLGD reader system with a coverage factor of k = 2 were calculated to be 9.26% from 0.005 to 1 Gy and 8.16% from 1 to 10 Gy. A blind test was conducted to validate the RPLGD reader system, which demonstrated that the readout doses included blind doses of 0.1, 1, 2, and 5 Gy. Overall, the E_n values were considered satisfactory.

In this paper, the swept source-optical coherence tomography system using frequency domain mode locked(FDML) laser has realized. The FDML swept source laser showed 55.03 kHz sweeping speed, 125 nm sweeping range, and 9 mW output optical power, which are the superiority of FDML laser compared to previous swept source lasers. Also, through the cross-sectional image captured at 5 frames per second for a mirror, a 1 mm-thickness glass plate, and a thumb bottom, the performance of the system has demonstrated.

스토버 방법(St$\ddot{o}$ber method)을 이용하여 균일한 크기의 실리카 나노비드(silica nanobead)를 합성하였으며 초음파(sonication) 방법을 이용하여 분자 처리된 유리 기판 위에 실리카 나노비드를 단층(monolayer)으로 정렬시켰다. 유리기판위에 처리된 분자층은 3-chloropropyltrimethoxysilane (CP-TMS)와 polyethyleneimine (PEI)가 사용되어졌고 합성된 나노비드는 톨루엔에 분산시킨 뒤 초음파방법으로 유기기판위에 부착되어졌다. 수행되어진 초음파방법은 분자 처리된 유리 기판을 단독으로 사용하는 SO (sonication without stacking) 모드와 두 개의 깨끗한 유리 기판 사이에 분자 처리된 유리 기판을 삽입하여 사용하는 SS (sonnication with stacking) 모드로 구분지어 적용되었으며, 기판위에 정렬된 실리카 나노비드의 무게는 마이크로 저울(microbalance)을 이용하여 측정한 뒤 점유도(degree of coverage, DOC)를 계산하였다. 결론적으로, SO 모드에서는 DOC가 단기간에 가파르게 상승하여 140% 이상까지 도달했지만 다층(multi-layer)구조가 많이 발견되는 특징이 있었고, SS 모드에서는 DOC가 평형에 도달하는 시간이 SO 모드보다 느리게 진행되었지만 보다 밀집(close-packing)된 형태의 단층구조가 관측되었다.

Uniform silica nanobeads were synthesized by St$\ddot{o}$ber method and assembled in the form of monolayer on glass substrate using sonication method. Before the assembly of silica nanobeads, glass substrates were treated with molecular linkers, such as CP-TMS and PEI, and nanobeads were dispersed in toluene. In attachment test, SO (sonication without stacking) method and SS (sonnication with stacking) method was used and sonication time was controled. After the experiment, microbalance was use to measure deviation between before and after the attachment experiment then calculate percent of coverage. Minutely observe with SEM (Scanning Electron Microscopy) then select the most close-packed and monolayer assembled cover glass and calculate DOC (Degree of Coverage). In SO method, DOC increased very sharply and reach over 140 percent point, also got lots of multi-layer region. On the other hand, in SS method DOC increased slower than SO method but more close-packed and monolayer assembled.

인공하천에서 탁수가 부착조류 군집에 미치는 영향을 평가한 연구는 실내에 인공수로 4개를 설치하고, 대조군 2개와 처리군 2개로 반복실험을 실시하였다. 사용된 기질은 1% agar을 바른 슬라이드 글라스($7.5{\times}2.5\;cm$)이었고, 지점당 40개씩 설치하였다. 조사는 2010년 3월 29일부터 4월 10일까지 총 13일간이었으며, 6일간은 부착조류가 부착할 수 있는 공백기를 주었고, 조사 7일부터 24시간 간격으로 약 50분(50 L)간 고농도의 탁수($2\;g\;L^{-1}$, 300 NTU)를 주입 시켰다. 분석항목은 수질요인(수온, DO, pH, 전기전도도, 탁도, SS, $NO_2$-N, $NO_3$-N, $NH_4$-N, $PO_4$-P, TN, TP)과 생물량(Chl-${\alpha}$, AFDM), 종조성올 분석하였다. 분석 결과, 처리군의 탁수 농도는 162.2~173.2 NTU로 나타났다. 탁수 발생에 따라 감소하는 경향을 보인 수질 항목은 수온, DO 및 TN으로 나타났고, 증가하는 경향을 보인 항목은 SS, $NO_2$-N, $NO_3$-N, $NH_4$-N 및 TP로 나타났다. 부착조류의 생물량(Chl-${\alpha}$, AFDM) 및 밀도는 탁수 주입 후 3 일간 크게 영향을 받지 않았으나 3일 이후부터는 뚜렷한 감소를 보였다. 본 연구의 결과는 단기간의 간헐적인 탁수라 할지라도 그 기간이 일주일 정도 지속된다면 부착 규조류 생물량을 크게 감소시킬 수 있음을 보여주었고, 그를 통한 하천 먹이사슬의 구조적, 기능적 교란의 잠재성을 시사한다.

We examined the effect of the turbid water on the periphytic diatom community in an artificial stream system. The artificial stream was constructed with transparent acryl and composed of four channels. Each channel ($20\;cm{\times}200\;cm{\times}40\;cm$) was supplied continuously with eutrophic lake water. In order to the freely colonize and grow diatoms, artificial substrate was installed with commercial slide glass soaked in 1% agar. Prior to introducing turbid water, the artificial stream was operated with lake water for 6 days to permit the propagation of diatom community on the substrates. The turbid water prepared with sediment sieved with ${\varphi}$ $64\;{\mu}m$ at $2\;g\;L^{-1}$ (final concentration, 300 NTU) was provided daily for 50 minute duration. The experiment was conducted for 7 days with manipulated experimental condition of light ($50{\sim}80\;{\mu}mol\;m^{-2}s^{-1}$, light:dark=24:0), temperature ($10{\pm}1^{\circ}C$), and flow rate ($0.31\;cm\;s^{-1}$). Sampling and analysis were conducted daily for water quality and diatom. Turbidity of the water varied 162.2~173.2 NTU during the experiment. After introduction of turbid water, DO, pH and TN were decreased, while SS and TP increased significantly. A total of 14 genera and 47 species of diatoms was observed on the artificial substrates during the experimental period. Of these, Navicula appeared to be a most dominant genus with 10 species, followed by Cymbella (6 species), Fragilaria (6 species) and Gomphonema (5 species). Achnanthes minutissima was the most dominant species (>70% of total frequency) in both control and treatment experiments. Increase in diatom abundance lasted for three days since turbid water introduction, after that they gradually decreased by the termination of the experiment. These results suggest that frequent supply of highly-concentrated turbid water significantly decreases the periphytic diatom community, and retard the recovery of the stable food-web within the stream.

본 연구에서는 우리나라의 분산지역 및 농촌마을의 하수처리를 위해 자연정화 고도처리 공법인 NEWS (Natural and Ecological Wastewater treatment System)를 적용하였다. 고친수성 biofilter를 사용하여 고형물질과 유기물질을 제거하였으며, 인공습지를 이용하여 영양물질을 제거하였다. 장지적으로 안정성을 갖으며, 부지면적과 효율 면에서 기계적인 공법과 경쟁할 수 있는 자연정화 고도처리공법을 개발하고자 고친수성 biofilter와 상하흐름형 인공습지를 조합하여 (NEWS)처리효과를 검토하였다. 본 처리시설을 적용한 결과 COD를 제외한 수질항목에서 높은 제거율을 나타내었다. Biofilter 유출수는 국내 수질기준을 만족시키지 못하였으나, 인공습지를 거쳐 처리된 최종 유출수는 수질기준을 만족시켰다. BOD, SS, TN, TP의 유입부하량과 제거량과의 관계를 회귀분석 한 결과 결정계수는 각각 0.998, 0.999, 0.919, 0.919로 매우 높은 상관성을 나타냈다. 동절기 효율저하의 문제점을 해결하기 위해 연구시설의 지붕을 투명 폴리카보네이트 글라스로 설치하여 난방을 하지 않는 온실을 도입하고, 12-2월 동안 겨울철 처리장 실내 ${\cdot}$ 외 온도차이를 측정한 결과 처리장실내온도가 실외 온도보다 최고 $20^{\circ}C$까지 높게 나타났다. 따라서 본 연구에서 개발한 자연생태학적 하수고도처리공법인 NEWS는 유기물질과 영양물질 처리공정을 분리하여 처리효율을 높일 수있으며, 국내의 분산지역 및 농촌마을의 하수처리에 적용가능성이 높을 것으로 판단된다.

The feasibility of the Natural and Ecological Wastewater treatment System (NEWS) was examined for rural wastewater treatment in Korea. The intermittent trickling biofilter with high hydrophilic filter media was used for pretreatment for suspended solids and organic pollutants. The subsequent constructed wetland with porous granule materials was used for promoting nutrient removal. The results show that the removal efficiencies of the system were high with respect to the water quality parameters except COD. Even if the effluent from the biofilter did not meet the guidelines for wastewater treatment plant effluent in Korea in terms of $BOD_5$ and TN, the final effluent of the system meets the guidelines us to good performance of the constructed wetland. The regression analysis between pollutant loading rate and removal rate indicated that the system could have stable removal for SS, $BOD_5$, TN, and TP in the given influent ranges. The analysis in the winter period indicated that the wetland covered with transparent polycarbonate glass had the statble performance during the winter period dus to increase of temperature inside the wetland without any heating system. With the stable performance, effective poilutant removal, low maintenance, and cost-effectiveness, the NEWS could be considered as an alternative treatment system for decentralized regions and rural communities in Korea.

본 연구는 하천에서 가뭄으로 인해 나타나는 갈수현상을 단기간의 유량의 감소로 모사하여 수질 및 부착돌말류 군집에 미치는 생태학적 영향을 인공수로에서 분석하였다. 아크릴로 제작한 실내 인공수로에 부착돌말 인공기질로는 슬라이드글라스를 설치하고, 부영양 저수지의 표층수를 유입시켜 실험수로 이용하였다. 실험기간 중 부착돌말 군체형성기 동안 모든 실험군의 유량은 6 L $min^{-1}$, 이후 유량감소기 동안 각 실험군의 유량은 NDF(No depletion of flow rate (Control): 6 L $min^{-1}$), LDF (Low depletion of flow rate: 3 L $min^{-1}$), 그리고 HDF (High depletion of flow rate: 1 L $min^{-1}$)로 설정하였다. 유량감소의 영향을 비교하기 위하여 16일간의 실험기간 동안 유입수와 배출수의 수온, 전기전도도, 용존산소, pH, 탁도, 부유물질, 영양염 및 Chl-$a$ 농도를 분석하였으며, 또한 부착기질의 Chl-$a$와 AFDM(ash free dry matter), 그리고 부착돌말류의 조성과 세포밀도를 1일 간격으로 분석하였다. 광도는 처리 유량이 적어질수록 유의하게 증가했다(F=229.5, p=0.000). $NH_4$-N는 NDF보다 HDF에서 현저하게 높은 농도를 유지하였다. 유입수의 SS 농도(100%) 대비 배출수의 SS 농도는 HDF에서 88%로 감소하였으며 LDF (97%)와 NDF (99%)에 비하여 높은 감소율을 보였다. 기질의 Chl-$a$는 NDF에 비하여 유량감소 처리군에서 약 2배 이상 유의하게 증가하였다(F=8.399, p=0.001). 또한 기질의 AFDM과 부착돌말류 총밀도는 NDF에 비하여 두 처리군에서 유의하게 증가하였다(F=9.390, p=0.001; F=6.088, p=0.007). 실험기간 동안 대조군과 처리군 모두에서 $Aulacoseira$ $ambigua$, $Achnanthes$ $minutissima$, $Aulacoseira$ $granulata$ 등 총 3종의 부착규조류가 총 밀도의 10% 이상을 보인 우점종으로 나타났고, 제1 우점종인 $A.$ $ambigua$는 LDF에서 가장 높은 밀도를 보였으며 HDF, NDF순으로 생물량이 낮았다(F=8.551, p=0.001). 본 연구 결과, 인공 하천생태계에서 가뭄(갈수) 효과는 수질과 부착돌말류 현존량에 유의한 변화를 야기하였으며, 특히 부착돌말류 현존량이 유의하게 증가하였다. 이는 실제 하천에서 가뭄에 의한 생태계의 변화를 이해하는데 유용한 기초자료를 제공할 것으로 사료된다.

We investigated an ecological impact of drought simulated by discharge depletion on the water quality and benthic diatom community in the indoor experimental channel. As artificial substrates slide-glass was installed in acrylic channel for 16 days. Channels were supplied continuously with eutrophic lake water with a discharge rate of 6 L $min^{-1}$ in duplication during the colonized period. And then during the discharge depletion period, three discharge rates were provided: NDF (No depletion of flow rate (Control): 6 L $min^{-1}$), LDF (Low depletion of flow rate: 3 L $min^{-1}$) and HDF (High depletion of flow rate: 1 L $min^{-1}$). Environmental factors in the water, such as suspended solid, Chl-$a$ and nutrients concentration, were measured with periphytic algae including AFDM (ash free dry matter), Chl-$a$ concentration and cell density at 1-day intervals. Light intensity increased significantly with discharge depletion (F=229.5, p= 0.000). $NH_4$-N concentration was highest at HDF. Suspended solid in outflowing water decreased at HDF (88%), LDF (97%) and NDF (99%), compared to inflowing water (100 %). Chl-$a$ in substrates increased more than two times at LDF and HDF than NDF (F= 8.399, p=0.001). Also AFDM and benthic diatom density increased significantly at LDF and HDF than NDF (F=9.390, p=0.001; F=6.088, p=0.007). In all experimental groups, $Aulacoseira$ $ambigua$, $Achnanthes$ $minutissima$ and $Aulacoseira$ $granulata$ were dominant species accounting for greater than 10% of benthic diatom density. The most dominant species, $A.$ $ambigua$ was highest at LDF, followed by HDF and NDF (F=8.551, p=0.001). In conclusion, the effect of drought simulated by discharge depletion in an artificial stream ecosystem caused significant changes on water quality and benthic diatom biomass. This result provides a useful data to understand the effect of draught on stream ecosystem in situ.

LAS($Li_2O-Al_2O_3-SiO_2$)계에 전이금속과 희토류 이온을 첨가한 글라스세라믹의 colouring에 대한 특성 분석이 이루어졌다. 투과성이 높고, 내열 충격성이 우수한 글라스세라믹을 제조한 수 있었으며, 주 결정상은 ${\beta}$-eucryptite(SS)이었다. 또한 colouring에 의한 빛의 흡수 특성과 이러한 글라스세라믹에서의 colouring 이온의 구조적 상태가 조사되었다.

내열 충격성 및 적외선 투과를 갖는 LAS($Li_2O-Al_2O_3-SiO_2$)계 글라스세라믹스를 제조하였다. 본 연구에서는 LAS계에 $TiO_2$를 핵형성제로, 점도를 감소시키기 위해 $P_2O_5$를 첨가하여 유리를 제조한 후, 글라스세라믹 결정상을 석출시켰다. 석출된 주 결정상은 ${\beta}$-eucryptite(SS)이었으며, 열팽창 계수가 거의 제로에 가까운 값을 얻었다. 또한 선택적인 스펙트럼의 흡수를 위한 color dopants에 대한 기초 자료 등이 조사되었다.

최근 전자제품 사용의 증가로 인해 버려지는 전자제품의 양도 함께 증가하고 있으며 이렇게 늘어난 전자폐기물이 부적절한 방식으로 처리될 경우 우리에게 악영향을 미치는 위험물질이 될 수 있다. 본 연구에서는 이러한 전자폐기물 중 하나인 폐 LCD 유리를 이용한 수질정화용 여재를 이용하여 전자폐기물에 의한 오염을 줄이고, 동시에 강우시 표면 유출로 인하여 발생되는 비점오염을 제어하고자 하였다. 본 연구에서 이용한 수처리 여재는 기존 수처리 여재의 단점을 보완하는 대체 여재 개발이라는 목적에 적합할 것으로 판단된다. 이에 본 연구에서 발포기술이 적용된 폐 LCD 유리 여재의 비점오염에 의한 수질정화능력평가를 하기 위해 실험 장치를 구성하여 실험하였다. 반응조는 직경 0.10 m, 높이 0.75 m 크기(총용량= 5.89 $\ell$)로 두께 10mm의 투명 아크릴판으로 3조를 제작하였다. 유입수는 미량 펌프를 이용하여 유입하였다. 각 반응조의 체류시간에 의한 수질정화능력을 평가하였다. 연구 결과, 오염물질에 대한 제거효율 범위는 SS $64.1%\sim88.2%$, BOD $29.8\sim52.4%$, COD $56.8\sim66.1%$, T-N $39.4\sim\;52.3%$, T-P $14.1\sim36.8%$로 나타났다. 체류시간이 가장 길었던 반응조의 경우, 대부분의 측정항목에서 높은 처리 효율을 볼 수 있었다. 초기에 처리 효율이 낮은 것은 미생물이 부착되지 않았기 때문이라고 판단되며, 실험의 중반과 후반에서 미생물이 부착이 되는 시점부터 높은 처리효율을 보이는 것으로 나타났다.

Generally beam design depends on the yielding and maximum strength of each member varying with its section shape. Web plate of H-shape beam has not been substituted with glass plate, because it is known that its strength and heat properties are different and it is limited to substitute the existing steel web with glass element. Ceiling height of each room should be decreased with more than 60-80cm due to the beam. Differently from this condition, glass web beam has a good point to see through it and sunshine can be penetrate into the other size especially when it is installed as of outside wall. And also, it can be safer due to controlling room inside easier, if the strength is applicate. This study is to show some applicability after finding out the properties using the test. The test members with a size of $1,600{\times}200{\times}300{\times}9mm$ being SS41 rolled steel having THK 9mm flange while having 8,10mm and reinforced glass 12mm thickness is bonded with epoxy bond under the condition of temperature $28^{\circ}C$, humidity 50%, bonding power 24Mpa. It is show reinforced glass has 5 times of fracture stress more than the common glass but $50{\sim}150%$ difference between these 2 kinds of glass was shown. Reinforce glass did not support the original upper flange after fracture but the common glass did the upper flange after unloading. Generally reinforced glass is stronger than the common one but the common glass having a part of crack on it, compared with reinforced glass having the overall fracture could be more useful in case of needing ductility.

In modern science and technology, the organization of building blocks, such as spherical particles and zeolite, is important to form a nanostructure. So, it is essential to develop methods for organizing them into large scale for many precise applications. Up to now, reflux and stirring is widely used method for organization of colloidal particles. However, because this method is hard to organize building block with high coverage and uniform orientation, it is necessary to research another method. In this work, we synthesized spherical silica particles using St$\"{o}$ber method and organized them on the glass which is coated with 3-chloropropyltrimethoxysilane (CP-TMS) and polyethyleneimine (PEI) using Sonication method. Although spherical silica particles are difficult to attach on the glass due to their small attachment site, we improved this problem by coating PEI. We introduced two mode of reaction promotion, sonication (SO) and sonication with stacking between the bare glass (SS), and investigated degree of coverage (DOC) and degree of close packing (DCP).

본 연구는 산업폐기물을 이용한 인공경량골재의 제조에 관한 실험적 연구이다. 실험결과, 산화슬래그를 부원료로 사용한 경우, 소성온도 $1,150^{\circ}C$에서 낮은 절건밀도와 낮은 흡수율을 나타내었고 유리연마슬러지의 경우는 본 연구에서 사용한 범위 이상을 사용하여야 경량화가 가능할 것으로 판단된다. 그러나 고로슬래그 미분말은 경량골재 원료로 사용하기에는 부적합한 것으로 판단된다.

This study is of manufacturing artificial lightweight aggregates using industrial wastes. The ingredients for manufacturing lightweight aggregate were stone sludge and bottom ash for main materials, and steel slag(SS), glass abrasive sludge(GS) and blast furnace slag(BS) respectively for accessory material. Their precursors were sintered in the range of $1,050{\sim}1,150^{\circ}C$ for 5 min. The sintered results show that the lightweight aggregate with SS had low water absorption ratio and density at $1,150^{\circ}C$. There's a possibility that if GS is used more than the range of this study, GS can be manufactured lightweight aggregate. But it is judged that BS are incongruent to be used for a raw material of lightweight aggregate.

The metallorganic chemical vapor deposition (MOCVD) method has been used to prepare TiO2 thin films for the degradation of hazardous organic compounds, such as 2-chlorophenol (2-CP). The effect of supporting materials and metal doping on the photocatalytic activity of TiO2 thin films also has been studied. TiO2 thin films were coated onto various supporting materials, including stainless steel cloth(SS), quartz glass tube (QGT), and silica gel (SG). Transition metals, such as Pd(II), Pt(IV), Nd(III) and Fe(III), were doped onto TiO2 thin film. The results indicate that Nd(Ⅲ) doping improves the photodegradation of 2-CP. Among all supporting materials studied, SS(37 ${\mu}m)$ appears to be the best support. An optimal amount of doping material at 1.0 percent (w/w) of TiO2-substrate thin film gives the best photodegration of 2-CP.

Molding of body with ribs is the most difficult during flow molding process. The rib area is easy to be deformed at the rear side due to wall thickness variation. In this study, relationships between molding condition and deflection of rib-shaped part is investigated during the compression molding of fiber reinforced plastic composites , and the following results are derived. Polypropylene(PP), Polystyrene(PS), and stampable sheet(SS 40wt%) show the increment of deflection along with releasing temperature. For the correlation between incremental holding pressure load and deflection, stampable sheet exhibits lower deflection along with higher holding pressure, while PS shows significant increase of deflection with higher holding pressure, PP shows completely different characteristic, significant reduction of deflection along with higher holding pressure. Regarding to mold temperature and deflection, deflection amount of SS is the biggest, and PS shows the smallest. In addition, all three kinds shows the highest amount of deflection at 173C. Deflection is reduced when mold closing speed is increased. Amount of deflection in SS is larger and is not highly dependent on molding conditions like holding pressure and cooling parameters, compared with single component material like PP. This can be elucidated by anisotropic and inhomogeneous characteristics of glass fiber during filling process of stampable sheet composite.