Earticle

Polyvinylchloride(PVC) polymer was spun to obtain PVC fiber mainly by dry spinning method in the past years. The present study investigated the method to manufacture a PVC fiber by melt spinning method. The PVC polymer mixed with heat resistant agent and lubricant was spun to obtain undrawn fiber. The undrawn fiber was drawn by the wet drawing process, and it was dried and heat-set to give a dimensional stability. The properties of the drawn fiber such as strength, elongation and heat shrinkage were changed with the spinning and drying conditions. The effects of the fiber manufacturing conditions on the properties of the fiber were investigated in this study.

The purpose of this study is to suggest the fundamental data for noise control design and standard criteria for PVC pipe by theoretical simulation and experimental research. To predict decibel noise pressure, the actual and theoretical test results by using PVC single pipe, PVC double pipe and PVC threefold-jointed, are carefully examined for the drainage facilities' nise in this study. Also, this study would presents fundamental informations and date on the reduction of the drainage facilities' noise by analyzing vibration modes of pipes. The major results are as follows; 1) The noise protect performance of double PVC pipe are prefer then single PVC pipe 10 dB condition. 2) Theoretical noise reduction effects for double PVC pope and threefold-jointed pipe are have similar effects in 2 KHz~4 KHz band and some differences are shown in low level Hz band.

본 연구에서는 norbornene dialkyl ester 8종을 PVC에 적용하여 물리적 물성의 변화를 관찰하였다. PVC 시편은 PVC와 norbornene dialkyl ester, 안정제 등을 배합하여 제작하였고, 경도, 인장강도, 신율, 인열강도, 투과도, 투명도, 황변지수를 측정하여 DOP를 적용한 경우와 비교하였다. 경도는 dicyclohexyl-5-norbornene-2,3-dicarboxylate (DCHN)를 제외한 화합물 7종이 DOP와 동등 이상의 값을 나타내었다. DCHN을 적용한 경우 경도가 매우 높아 인장 특성 및 인열강도를 분석하지 못하였다. 인장 특성은 diisononyl-5-norbornene-2,3-dicarboxylate (DINN)을 제외한 6종의 화합물이 인장강도와 신율이 모두 개선되는 결과를 나타내었다. 인열강도와 투과도는 측정된 모든 화합물이 DOP를 적용한 경우와 동등 이상의 물성을 보였으며, 투명도는 DDN을 제외한 다른 norbornene 유도체들은 양호한 상태를 나타내었다. 황변지수에서는 DPN과 DON이 DOP와 유사한 결과를 나타내었다.

In this study, we observed changes in the physical properties of norbornene dialkyl ester applied to a PVC. The PVC specimens were prepared by blending PVC, norbornene dialkyl ester and stabilizers. Then, the hardness, tensile strength, elongation, tearing strength, transmittancy, haze and yellowness index of these specimens were measured, and were compared with DOP. The hardness of compounds except dicyclohexyl-5-norbornene-2,3-dicarboxylate (DCHN) were an equal to or higher than that of DOP. The tearing strength and tensile characteristic of DCHN could not be analyzed due to its high hardness. Tensile properties such as the tensile strength and elongation were improved for six compounds except diisononyl-5-norbornene-2,3-dicarboxylate (DINN). All compounds measured showed better tearing strength and transmittancy than those of DOP. Also all norbornene derivatives except DDN showed good haze indices. The yellowness index of DON and DPN showed similar values as DOP.

케이싱 구간에서 얻어진 밀도검층 자료에 대한 보정연구의 일환으로 모형공에서 PVC 케이싱의 인위적 이격을 이용한 이격보정 연구를 실시하였다. 케이싱의 유형과 공벽으로부터의 이격의 정도, 공내 유체의 존재에 따른 검출기의 반응양상의 변회를 추적하였으며 특히 동일한 이격환경에서 시추공 내에 물이 있을 때와 물이 없는 상태에서 얻어진 이격반응에 대한 비교 분석이 집중적으로 수행되었다. 이로부터 PVC 케이싱에서 수행되는 밀도검층에서 공벽과 검출기 사이의 이격 거리에 따른 감마선 반응 특성을 정량화할 수 있었으며 이격보정 차트가 작성되고 지하수면 하부구간과 상부구간에서의 각 이격오차보정의 효과와 한계가 밝혀졌다.

A series of model borehole experiments and analyses for density compensation were performed to achieve the effective density correction of gamma-gamma log obtained from PVC cased boreholes. A follow-up survey was made for clarifying the variation property of detector responses depending on casing types, the presence of borehole fluid, and the degree of separation between probe and borehole wall. A special emphasis was placed on the comparison of gamma responses obtained from above and below ground water tables. Finally, we could quantify the detector responses as a function of separation between the probe and borehole wall, construct standoff compensation charts, and the limitations of the compensation have been discussed for the environments of both above and below ground water tables.

Following a Mediterranean fruit fly outbreak in South Australia, a bait spray program involving the pesticides like malathion(MAL) was carried out. During the application, dermal exposure was considered for the pest controllers wearing PVC gloves. However there is a lack of information about PVC glove performance like break through times and permeation rates with MAL, therefore, a new analytical method for HPLC-UV was developed. A standard permeation test cell was used in this study. From the results of this study, more than 96% solubility of MAL was provided at 30% isopropyl alcohol in distilled water as a collecting media. However, there was significant decomposition of MAL when the solutions were kept at over $50^{\circ}C$ for 2-3 hours. As a mobile phase, 50% acetonitrile water solution (pH 6.0) gave the greater sensitivity compared with other compositions of acetonitrile solution. The arm section of the gloves had shorter breakthrough times and higher permeation rates compared with the palm. There was no malathion solution breakthrough up to 24 hours using the 1% MAL working strength solution. When the temperature was changed from $22{\pm}1^{\circ}C\;to\;37{\pm}1^{\circ}C$, the breakthrough times were decreased by 14.5% on palm and 37.5% on arm, and permeation rates were increased significantly. The findings of this study indicate that further investigations on used gloves, periods of use and varying working conditions like tasks and seasons should be carried out to assess potential worst case scenarios.

공기분위기에서 PVC와 PS의 혼합 분해시 ZnO의 영향에 관한 연구를 혼합비율 및 반응온도를 변화시키며 TG와 GC-MS를 이용하여 수행하였다. 본 연구로부터 혼합물에 있어서 PS의 양이 증가할수록 액상 생성물은 증가하였으며 기상 생성물은 감소함을 알 수 있었다. 또한 혼합물에 있어서 ZnO의 첨가량이 증가할수록 가스 생성물과 염화수소의 발생량은 감소하였으며 ZnO/Mixture = 0.5인 경우 ZnO의 영향에 의하여 염화수소가 거의 생성되지 않음을 확인할 수 있었다.

The effect of ZnO in the decomposition of poly(vinyl chloride) (PVC) and polystyrene (PS) mixtures in air atmosphere has been studied by thermogravimetry (TG) and gas chromatograph-mass spectrometry (GC-MS) under various mixing ratios and reaction temperatures. From this work, it can be seen that the yields of a liquid product were increased with the increase of PS in mixtures, whereas those of gaseous products were decreased. And the yields of a gaseous product and HCl were decreased with the increase of ZnO in mixtures. It was also found that HCl was rarely produced at ZnO/Mixture = 0.5 by the effect of ZnO in dehydrochlorination of PVC.

PVC를 염색하는 방법에는 분산염료, vat 염료, 함금속염료, 산성염료 등이 보고되고 있다. 그러나 PVC는 의류용 사로 적용되는 예가 적기 때문에 이의 염색에 대한 연구 결과도 상대적으로 드물다. 가발용 사를 만드는 공정의 경우 PVC 방사 시 안료를 배합해 유색 PVC를 얻는 방법에 대한 문헌이 약간 있을 뿐 PVC의 염색에 관한 자료는 거의 찾아보기가 힘들다. 최근 PVC 사의 용도가 다양해지고 있고, 가발용 원사로 이용되는 경우 안료를 배합한 방사법만으로는 two tone colour 등 가발용 원사로서의 다양한 요구에 부합되지 못하므로 후염색에 의해 PVC를 염색하는 방법의 필요성이 요구된다. (중략)

고분자가 절연재료로서 사용되는 이유는 전기를 통하지 않는 절연특성을 지니고 있기 때문이며 이러한 성질은 고분자가 금속재료와 구별되는 가장 큰 특징이다. 그러나 1964년 W. A. Little 이 발표한 공액 이중결합구조를 가진 화합물은 전도성 고분자가 될 수 있다는 가설을 바탕으로 전도성 고분자에 관한 많은 연구가 진행 중에 있다. 전도성 고분자는 절연체로서의 응용에만 한정되어왔던 기존 고분자물질들과 달리 가볍고 저렴하며 단일결합과 이중결합을 교대로 하고 있는 공액 고분자 구조를 가지고 있어 다양한 화학적 합성방법에 의해 전기전도도, 유전상수, 결정 등의 물리적 성질을 조절할 수 있으며, 금속의 전기적, 자기적, 광학적 특성과 고분자의 기계적 성질을 동시에 가지므로 배터리, 축전기, 트랜지스터, 광전소자, 전자파 차폐제 등 플라스틱 전자소재의 실용적으로 인해 산업체에서도 높은 관심의 대상이다. (중략)

Since a drawn fiber shrinks when treated with heat, fiber is treated with heat after drawing process to prevent heat shrinkage. The objective of this study is to investigate the effects of drawing conditions on the properties of PVC fiber, especially on heat shrinkage. Overfeed was applied to prevent heat shrinkage at the several positions during drawing process. Heat shrinkage increased with draw ratio, and decreased with overfeed ratio. Overfeed was most effective to reduce heat shrinkage when applied between the chamber 2 roller and the take-up roller. The chlorinated PVC(CPVC) content also affected the heat shrinkage, and heat shrinkage decreased with increasing CPVC ratio.

Four model blends (1: 1 by wt) of polyvinyl chloride (PVC) with three compatible (butadience-acrylonitrile copolymer elastomer having acrylonitrile content of 3O%, poly-ε-cap-rolactone, copolyester thermoplastic elastomer) and one incompatible (butadience-acrylonitrile copolymer elastomer having acrylonitrile content of 22%) polymers were investigated in this study The dynamic mechnical measurements at small shear deformation were performed and the resulting data were presented in the form of log-log plot of loss modulus G"(ω) against storage modulus G'(ω). This plot, so called the Cole-Cole plot, was used as one of the methods for characterizing the viscoelastic behavior as well as the morphological changes of four model blend systems.

열가소성고분자에 첨가되는 가소제는 외부로의 용출로 인해 제품의 수명을 단축시키고, 일부는 환경, 인체에 유해한 영향을 미치는 것으로 알려져 있다. 발암물질로 의심되는 프탈레이트계 가소제의 사용이 점차 금지됨에 따라 이를 대체할 수 있는 친환경 가소제에 대한 필요성이 요구되며 대부분의 물질은 수지와의 상용성이 다소 떨어지거나 단가가 높으며 구체적인 안전성 검증이 부족한 문제가 있다. 따라서, 본 연구에서는 대체 가소제 후보물질로서 우수한 물리적 물성과 독성 평가에서 안전한 화합물로 보고되어진 노보넨 다이알킬에스터 화합물 4종을 PVC 수지에 첨가하여 용출에 의한 인체 노출 가능성을 평가하고 상용가소제 DEHP, DINCH, DOTP와 비교 분석하여 대체 물질로서의 가능성을 평가하고자 하였다. 시험은 american standard test method (ASTM) 규격에 준하여 시행하였으며 결과에 따르면, 수성 용매에서 di-2-ethylhexyl-5-norbornene-2,3-dicarboxylate (DEHN), 유성용매에서 diisopentyl-5-norbornene-2,3-dicarboxylate (DIPN) 화합물이 DEHP 대비 우수하거나 동등한 수치를 나타내었다. 또한 4종의 노보넨 화합물 모두 환경에 영향을 미칠 수 있는 수준으로 평가되는 100 ppm보다 낮은 수치를 나타내었으며 이는 극성부인 노보넨 구조가 용출성에 영향을 미친 것으로 보여진다.

Plasticizers added to thermoplastic polymers are known to shorten the life of products due to the elution to outside, and some of them are harmful to our environment and human body. Since the use of phthalate plasticizers suspected of being carcinogens has been gradually prohibited, there is a need for environmentally friendly plasticizers that can replace them. Most of the substances have a low compatibility with resin, high cost and lack of safety verification. Therefore, in this study, four kinds of norbornene dialkyl ester compounds possessing excellent physical properties, which are also reported as safe compounds from the toxicity evaluation, were added to PVC resin to evaluate the possibility of human exposure by leaching, and also the potential usage as plasticizer candidates alternative to commercial ones including DEHP, DINCH and DOTP. The test was carried out according to the American standard test method (ASTM). The results showed that di-2-ethylhexyl-5-norbornene-2,3-dicarboxylate (DEHN) in aqueous solvents and diisopentyl-5-norbornene-2,3-dicarboxylate (DIPN) compounds in oil solvents were superior or equivalent to DEHP. In addition, all four norbornene compounds showed lower values than 100 ppm, which is considered to have an influence on the environment, indicating that the polar norbornene structure affects the elution.

The light weight composite materials have been replacing in high performance structures. The object of this study is to examine the effects of the initial crack location about a delamination in a PVC foam cored sandwich composite that is used for the strength improvement of structures. The initial crack location and fiber laminates thickness were changed with several types. The MMB specimen was used for evaluating the fracture toughness and crack behaviors. The material used in the experiment is a commercial twill carbon prepreg in CFRP material and Airex in PVC foam core. Sandwich laminate composites are composed by PVC foam core layer between CFRP face sheets. The face sheets were fabricated as 2 types of 5 and 8 plies. The initial cracks were located in a PVC form core and the interface of upper CFRP sheet. From the results, the crack initiation was affected with the location of the initial crack inserted in the PVC foam core. Among them, the initial crack at 1/3 of the upper part of the PVC foam core was the most rapid progression. And the critical energy release rate was $0.40kJ/m^2$, which is the lowest value when the initial crack was inserted into the interface between a PVC foam core and CFRP laminated with 5 plies. Meanwhile, the highest value of $1.27kJ/m^2$ was obtained when the initial crack was located at the center line in case of the 8 plies.

A series of model tests was carried out to investigate the vortex-induced vibration (VIV) characteristics of a free hanging PVC pipe under forced oscillation conditions. The prescribed displacement with a period and amplitude was forced at the top of the riser. The motion of the riser along its length was measured with underwater cameras in three dimensions. The top-excited responses in the inline direction and vortex-induced vibration in the cross-flow direction were examined in the time and frequency domains. Multi-peak frequencies in the VIV were demonstrated to be strongly dependent upon the Keulegan-Carpenter number, corresponding with the results of Blevin. It was found that the Reynolds numbers (excitation period) was a critical parameter for the dominant VIV characteristics, even under the condition of using the same Keulegan-Carpenter number, under the top-excited condition. In the resonance at the nth natural frequency by the forced-motion induced VIV frequency, the riser responded with a large amplitude and forced frequency, dominantly in the VIV CF direction.

열수축성 튜브 제조에 적합한 조성을 얻기 위하여 PVC의 방사선가교에 대하여 검토하였다. 중합도가 각각 다른 PVC에 가소제, 가교제를 변화시켜 배합한 혼합물을 방사선 가교시켰을 때 가교도는 가교제, 가소제, 중합도 및 조사선량이 증가됨에 따라 증가되었다. 가교제로서는 삼관능성 단량체가 높은 가교효율을 나타내었다. 가교 PVC 필름의 열수축성은 연신배율과 수축 온도를 높여줌으로써 증가되었으나 가교제 및 가소제의 증가량에 의한 열수축성의 증가는 나타내지 않았고 저중합도 PVC의 열수축성은 극히 저조하였다.

패러럴 슬라이드 게이트밸브는 복합발전플랜트 배열회수보일러와 증기터빈 사이에 위치하여 증기유동의 흐름을 제어하는 밸브로서 운전기간 동안 기동, 부하변동 및 정지 등의 운전이 반복적으로 이루어진다. 따라서, 각 기동운전 중에 밸브 두께 방향의 온도 차이로 인하여 발생하는 큰 압축 열응력으로 인한 피로손상 및 구조건전성에 대한 평가가 필요하다. 본 논문에서는 배열회수보일러의 주중기 밸브로 설치되는 16인치 패러럴 슬라이드 게이트밸브의 피로수명 평가를 위한 열구조해석 및 ASME B&PVC VIII-2에서 제시된 탄성응력해석 및 등가응력에 기반한 피로수명 평가를 수행하였다.

A parallel slide gate valve (PSGV) is located between the heat recovery steam generator (HRSG) and the steam turbine in a combined cycle power plant (CCPP). It is used to control the flow of steam and runs with repetitive operations such as startups, load changes, and shutdowns during its operation period. Therefore, it is necessary to evaluate the fatigue damage and the structural integrity under a large compressive thermal stress due to the temperature difference through the valve wall thickness during the startup operations. In this paper, the thermal-structural analysis and the fatigue life evaluation of a 16-inch PSGV, which is installed on the HP steam line, is performed according to the fatigue life assessment method described in the ASME B&PVC VIII-2; the method uses the equivalent stress from the elastic stress analysis.

500나노 입자 및 기본 물성이 우수한 이중층상구조금속수화물(LDH)를 합성하고 PVC 수지에 적용하여 고온, 저온열안정성 및 가공특성으로 인장강도, 신율, 체적저항 등이 우수한 시제품을 합성한 후 개발한 이중층상구조금속수화물(LDH) 시제품을 사용하여 무독성안정제(금속석검계), 내외부활제류, 가공조제, 산화방지제 등 기타 첨가제 등을 사용하여 PVC수지에 적용하여 수지배합에 따른 시험편을 제작하여 배합비별로 고온, 및 저온열안정성, 체적고유저항, 가공성(인장강도, 신율 등), 내후성, 초기 착색성 등 물성, 기계적 가공특성 및 성능이 우수한 할로겐수지용 무독성배합을 개발한다. 최종적으로 개발한 이중층상구조금속수화물(LDH)을 사용하여 제조하여 PVC 수지의 열안정성 및 기계적 가공특성이 우수한 중금속계대체용 무독성복합열안정제를 개발하였다.

The cetylpyridium ion-selective electrode were developed by dibenzo-18-crown-6 for auto control of the chemical plants. The effect of content of active material and the membrane thickness on the response characteristics of electrode such as the linear reponse range, the detection limit, and Nemstian slope of the electrod, were studied. The electrode characteristics was better with decreasing the content of active material above the optimum content, but became worse below these. DBP was best as a plasticizer, The effect of the membrane thickness on the electrode characteristics was improved with decreasing the membrane thickness, but below the optimum membrane thickness the electrode exhibited an inverse trend.