Earticle

The number of aged bridges is increasing so that bridges over 30 years old account for about 11% of all bridges. Consequently, the development of a seismic performance evaluation method that considers the effects of ageing is essential for a seismic retrofitting process for improvement of the seismic safety of existing old bridges. Assessment of the damage situation of bridges after the recent earthquakes in Korea has been limited to the bearings, anchor, and concrete mortar on piers. The purpose of this study is to evaluate the seismic responses of PSC box girder bridges by considering the ageing effect of rubber bearings (RBs) and lead-rubber bearings (LRBs). The modification factor proposed by AASHTO is used to take into account the ageing effect in the bearings. PSC box girder bridges with RBs and LRBs were 3D modeled and analyzed with the OpenSEES program. In order to evaluate the ageing effect of RBs and LRBs, 40 near fault and 40 far field records were used as the input earthquakes. When considering the effect of ageing, the displacement responses and shear forces of bridge bearings (RBs and LRBs) were found to increase mostly under the analytical conditions. It was shown that the effect of ageing is greater in the case of RBs than in the case of LRBs.

연속교의 교대부와 교각부에 설치되는 받침 용량은 통상적으로 각 지점에 작용하는 최대수직반력의 크기에 따라 결정되며 교각부에 더 큰 용량의 받침이 위치한다. 본 연구에서는 지진격리장치가 적용된 세 가지 받침배치에 따른 사교의 지진거동 변화를 비교 분석하여 연속 사교의 지진성능 향상 가능성을 검토하였다. 기존 받침배치(Case A)를 기준으로 교각부에 설치되는 납고무받침(LRB)의 수평강성에 변화를 주어 세 가지 받침배치(Case A, Case B, Case C)를 선정하였다. 납고무받침 자체의 감쇠효과가 고려된 hybrid response spectrum을 이용한 응답스펙트럼 해석을 수행하여 총 36개의 연속 플레이트 거더 사교들의 지진거동을 조사하였다. 해석결과 교대부에 설치된 LRB와 유사한 수평강성 또는 작은 수평강성을 가진 LRB를 교각부에 설치할 때 훨씬 바람직한 사교의 지진거동이 유발되었다. 즉, 교각부에 설치되는 LRB의 수평강성 변화는 사교의 고유진동주기를 길게 하고 모드형상에 변화를 유발시켜 전체밑면전단력과 교각부에서의 최대밑면전단력 그리고 거더에 걸리는 응력을 크게 감소시킨다. 비록 하부구조의 유연성이 증가할수록 받침배치 변경에 따른 지진거동의 긍정적인 효과가 다소 감소되지만, 10m 미만의 교각 높이를 가지면서 지진격리받침(LRB)이 설치된 연속 플레이트 거더 사교의 경우 제안된 받침배치는 지진성능 향상을 가져온다.

The capacity of bearings installed at abutments and piers for continuous bridges is usually determined by the magnitude of the maximum vertical reaction at each support and the capacity of bearings placed at piers is higher than that at abutments. In this study, the possibility of the improved seismic performance of base-isolated continuous skew bridges was investigated by analysing the variation of the seismic behavior of them according to three arrangements of bearings. Based on the conventional arrangement of bearings(Case A), three arrangements of bearings such as Case A, Case B and Case C were selected considering the variation of the horizontal stiffness of the lead rubber bearing(LRB) installed at the pier. The seismic behavior of the total 36 skew bridges was investigated by conducting the response spectrum analysis using the hybrid response spectrum considered the effect of LRB's damping. Results of analyses show that a more desirable seismic behavior of base-isolated continuous skew bridges can be obtained by reducing the magnitude of the horizontal stiffness of LRB placed at the pier to similar to or less than that of LRB installed at abutments. The variation of LRB's stiffness at the pier brings about period elongation and the change of mode shapes of base-isolated skew bridges and results in the reduction of the total base shear, the maximum base shear at the pier and the girder stresses. Although positive effects on the seismic behavior of base-isolated skew bridges caused by the change of arrangement of bearings decreased slighty with an increase in the flexibility of the substructure, the proposed arrangements of bearings bring about the improved seismic performance of base-isolated continuous skew plate girder bridges with less than 10m height of piers.

Superstructure of reinforced concrete bridges are shortened or elongated due to creep, drying shrinkage, temperature and so on. Most of bridge superstructures are free to shortening and elongation without constraint and stresses will not be induced by creep, drying shrinkage and temperature. But if bridge superstructure are constraint due to wrong setting and functional defects of bridge bearing, very large constraint forces can be induced. In this study, PSCI-Beam by tilt-constructed with constraint and deviation of bearings are presented and the effects of time-dependent constraint stress and temperature loads are investigated.

In this study a 3-dimensional analytical model is developed, which can analyses dynamic responses of curved bridges subject to moving vehicles. A 5-axle semi-trailer is modeled to simulate the actual tire forces that are redistributed by vehicle rolling effect due to the centrifugal force. The 1-span curved bridge with two steel box girders is modeled using the frame elements. The dynamic response characteristics of curved box girder bridges are examined and compared for two different support conditions. One is the case that two shoes are arranged at the outer sides of box girders with larger space between the two shoes and the other is that two shoes at the center of each box girder. In the curved bridges, the dynamic effect of moving vehicles influences the reaction force much more than other responses, such as displacement or stress, especially the upward reaction of inner-radius shoes. It is more advantageous for the reaction considering dynamic effect when shoes are arranged further at the outer sides of box girders than when shoes at the center of each box. The shoes for curved bridges with two-box girder system should be arranged to have larger distance.

Dynamic responses of a multi-span simply supported bridge are examined under seismic excitations considering damage of bearings. An idealized mechanical model which can consider components such as pounding, friction at the supports, abutment-soil interaction, rotational and translational motions of foundations, and the nonlinear pier motions, is developed to analyze the effects due to damage of bearings. It is assumed that the bearing's response after failure can be expressed with a sliding model with a friction coefficient between the superstructure and the pier top. It is found that the global seismic behaviors are significantly influenced by the damage of bearings and the damage of bearings may lead to unseating failure at unpredicted supports. Therefore, It can be concluded that detailed seismic response analyses of bridge systems considering damage of bearings is required for the purpose of the seismic safety evaluation.

이상신, 2019, 겹받침 관련 어문 규정 연구, 182 : 5~26 본고의 목적은 공통적으로 겹받침을 대상으로 하고 있는 ‘한글 맞춤법’ 제21항과 ‘표준 발음법’ 제10, 11항의 관련성을 중심으로 어문 규정의 합리성과 명료성 그리고 정합성을 검토하는 것이었다. ‘한글 맞춤법’ 제21항을 검토한 3.1.에서는, 지금으로서는 겹받침의 끝소리가 드러나지 않으면 ‘자음¹자음²’ 중 ‘자음¹’만 표기하도록 한 ‘다만’과 ‘1.’에 제시된 예시어 ‘값지다’와 ‘넋두리’는 상충(相衝)하는 것으로 오해될 여지가 있다는 점 등을 지적하였다. 겹받침과 관련되어 있는 ‘표준 발음법’ 조항들을 검토한 3.2.에서는, 총칭하여 ‘겹받침’이라는 용어를 쓰고 있는 제14항은 수긍하기 어렵다는 점 등을 지적하였다. 4장에서는 3장의 관찰을 바탕으로 하여 ‘한글 맞춤법’ 제21항과 ‘표준 발음법’ 제10, 11항의 관련성을 확인한 뒤, 이를 바탕으로 이들 규정 간의 정합성을 검토하였는데, 첫째, ‘ㄼ’과 관련하여 ‘한글 맞춤법’과 ‘표준 발음법’의 모순을 없애기 위해 선행 연구에 의지하여 ‘넓적하다’의 표기를 ‘넙적하다’로 수정하여야 함을 말하였고, 둘째, ‘ㄺ’과 관련하여 ‘한글 맞춤법’과 ‘표준 발음법’의 모순을 없애기 위해 ‘한글 맞춤법’ 제21항의 ‘다만 (1)’의 예 일부를 ‘다만 (2)’로 옮길 여지가 있는지 검토할 필요가 있음을 말하였다.

The purpose of this study is to examine the rationality, clarity, and consistency of the regulation of standard Korean centered on final double consonants. First, in Chapter 2, we briefly reviewed the terms related to final double consonants. In Chapter 3, we carefully observed whether the regulation of standard Korean related to final double consonants is rational and clear. Based on this, in Chapter 4, we examined the consistency between Korean Orthography and the Regulation of Standard Korean Pronunciation related to final double consonants.

이 연구는 초등학생들이 받침의 연음을 정확하게 하고, 발음 오류를 교정할 수있도록 연음 학습 단계를 설정하고 이를 기반으로 효과적인 교재 구성 방안을 찾기 위한 것이다. 연음 교육을 위해 <표준 발음법> 13항과 15항을 중심으로 ‘연음 조건(앞 음절받침의 종류, 뒤 음절 초성의 종류), 연음 방법’이라는 두 가지 요소를 고려해야한다. 연음 조건 두 가지를 조합하고, 연음이 된 후에 발음이 변한 구개음화도 연음유형으로 포함하여 연음의 유형을 네 가지로 정리하였다. 용례의 수가 적고 사용빈도가 낮은 유형을 제외한 나머지 유형으로 연음 학습 3단계를 선정하였다. 효과적인 연음 학습 교재 구성을 위해서는 연음 원리 학습 강화와 언어 자료의위계적 배열을 고려해야 한다. 교재에는 연음의 조건과 연음 방법을 나누어 제시하는데, 이를 지속적으로 환기할 수 있는 다양한 반복 활동을 배열하여 연음 원리를 체득할 수 있도록 한다. 이를 위해서 언어 자료의 단위는 낱말과 한 어절에서어구나 문장, 문단으로 점차 확장하도록 하고, 언어 자료의 학습자 친숙성, 음절수, 연음의 위치, 연음의 횟수에 따라 발생하는 난도를 고려하여 쉬운 수준에서 어려운수준으로 배열한다. 이 연구는 학생들의 연음 지도 자료로서 교과서의 보조 자료로 활용할 수 있으며, 받아쓰기와 연계하여 언어 자료를 불러 주는 방법에 대한 지침으로 활용할수 있다. 마지막으로 교사들의 연음 교육용 자료로 활용 가능하다.

In this study, considering the expansion/contraction behavior of the upper structure at all times and the abnormal behavior of the receiving friction elements that allow horizontal movement during earthquakes, a port receiving test body simulating the protrusion of the friction elements was created and the modulus performance was evaluated. In order to confirm the influence of the friction element's projection, the friction element's degree of separation was divided into four stages, and the shear behavior of the test specimen and the friction coefficient were confirmed. As a result of the experiment, it was found that the friction load increases as the protrusion degree of the friction element increases. On the other hand, as the degree of protrusion of the coefficient of friction increases, the coefficient of friction also increases. It was confirmed that damage to the friction elements during use increases the coefficient of friction, hinders smooth expansion and contraction of the upper structure, and causes stress concentration at the fixed-end support.

본 논문은 기존의 교량받침 마찰재인 PTFE의 내구성을 보완하고 낮은 마찰계수 발현 및 윤활제 미사용에서 마찰거동을 할 수 있는 세라믹 소재의 교량받침 적용을 위한 연구를 수행하였다. 세라믹 소재는 지르코니아계(ZrO₂)를 설정하였으며, 조도계수에 따른 마찰거동 평가를 수행하였다. 조도계수는 0.8 및 0.027로 구분하였으며, 15 MPa 면압조건에서 평균마찰계수는 모두 0.16으로 산정되었다. 이후, 세라믹을 마찰재로 제작하여 교량받침에 적용하였으며, PTFE 적용 교량받침과의 압축실험 및 마찰실험을 통해 성능비교를 수행하였다. 압축실험에서 세라믹 및 PTFE 적용 교량받침은 하중 재하에 따라 이상적인 압축거동을 나타냈다. 세라믹 적용 교량받침은 파손 및 결함이 관찰되지 않았지만, PTFE 적용 교량받침에서는 윤활제 소실이 관찰되었다. 마찰거동을 통해 분석한 세라믹 적용 교량받침의 평균마찰계수는 0.16으로 나타났다. 세라믹의 물리적 및 화학적 특성의 고유 재료물성과 성능평가를 통해 도출된 우수한 역학적 특성 및 0.16 수준의 마찰계수는 마찰재로써 고려할 수 있는 가능성을 제시한다.

This paper conducted a study on the application of ceramic materials for bridge bearing that can complement the durability of PTFE, a conventional bridge bearing friction material, and exhibit low coefficient of friction and friction behavior without lubricant. The ceramic material was zirconia (ZrO₂), and the friction behavior was evaluated according to the roughness coefficient. The roughness coefficient was divided into 0.8 and 0.027, and the average coefficient of friction was calculated to be 0.16 under 15 MPa surface pressure. Afterward, ceramic was made into friction material and applied to the bridge bearing, and performance comparison with PTFE bridge bearing was conducted through compression test and friction test. In the compression test, the ceramic and PTFE bridge bearing showed ideal compression behavior depending on the load. No fractures or defects were observed in the ceramic bridg bearing, but lubricant loss was observed in the PTFE bridge bearing. The average coefficient of friction of the ceramic bridge bearing analyzed through friction behavior was 0.16. The inherent material properties of the physical and chemical properties of ceramics, the excellent mechanical properties derived from the performance evaluation, and the coefficient of friction of 0.16 suggest that it can be considered as a friction material.

재료 및 부재의 내진성능평가 실험 시 재하속도와 수직하중은 성능에 중대한 영향을 미칠 수 있다. 반복 가력 및 하이브리드 실험 시 재하속도는 입력 변위와 출력 변위 사이의 시간 지연현상으로 인해 고속으로 제어하기 어려우며 횡방향 변위에 의해 수직하중을 일정하게 유지하는 것이 어려워 일정한 수직하중이 유지되는 고속 및 실시간 실험은 거의 이루어지지 않았다. 본 연구에서는 면진받침의 속도 의존성과 수직하중의 영향을 조사하기 위해 저속 및 고속 반복 가력 실험과 실시간 하이브리드 실험을 수행하였다. 실험에서 수평 변위와 수직 하중의 실시간 제어를 위해 Adaptive Time Series(ATS) 보정 방법과 State estimator가 포함된 FLB System을 구축하였다. 고속 또는 실시간으로 재하되는 수평 변위 제어 속도와 상부구조물에 의한 수직하중은 면진받침의 강도 및 지진 시 거동에 상당한 영향을 미칠 수 있음을 확인하였으며 내진성능평가를 위한 실험 시 실제와 유사하도록 구현되어야함을 알 수 있었다. 본 연구는 내진성능평가를 위해 구축하고 사용된 시스템의 우수한 성능을 보여주며 정확하고 효율적인 내진성능평가가 가능하도록 하였다.

In the evaluation of seismic performance for structural materials and components, the loading rate and axial force can have a significant impact. Due to time-delay effects between input and output displacements, It is difficult to apply high-rate displacement in cyclic tests and hybrid simulations. Additionally, the difficulty of maintaining a consistent vertical load in the presence of lateral displacement has limited fast and real-time tests performed while maintaining a constant vertical load. In this study, slow, fast cyclic tests and real-time hybrid simulations were conducted to investigate the rate dependency and the influence of vertical loads of Isolation Bearing. In the experiment, the FLB System including an Adaptive Time Series (ATS) compensation and a state estimator was constructed for real-time control of displacement and vertical load. It was found that the vertical load from the superstructure and loading rate can have a significant impact on the strength of the seismic isolation bearing and its behavior during an earthquake. When conducting experiments for seismic performance evaluation, they must be implemented to be similar to reality. This study demonstrates the excellent performance of the system built and used for seismic performance evaluation and enables accurate and efficient seismic performance evaluation.

An elastic bearing must be strong against vertical loads and flexible against horizontal loads. However, due to the material characteristics of rubber, it may show variability due to the manufacturing process and environmental factors. If the value applied in the bridge design stage and the actual measured value have different values or if the performance during operation changes, the performance required in the design stage may not be achieved. In this paper, the seismic response of bridges was compared and analyzed by assuming a case where quality deviation occurs during construction compared to the design value for elastic bearings, which have not only always served as traditional bearings but also have had many applications in recent seismic reinforcement. The bearing's vertical stiffness and shear stiffness deviation were considered separately for the quality deviation. In order to investigate the seismic response, a time history analysis was performed using artificial seismic waves. The results confirmed that the change in the bearing's shear stiffness affects the natural period and response of the structure.

평면내 곡선교량은 편심하중뿐만 아니라 자중만으로도 비틀림하중을 받게 되고, 이는 지점부 부반력 발생의 원인이 된다. 본 논문에서는 경간장 48.8m를 가지는 단경간 곡선강박스 거더교량에 대해 내부곡률각도를 0.49~1.35rad으로 조정하면서 곡률효과에 따라 지점에서 발생하는 수직반력을 분석하였다. 부반력 발생가능성을 고려하여 반력 크기 및 방향을 예측하기 위해 곡선교량 상부구조를 각 독립된 요소로 분리하여 반력산정식을 해석적으로 개발하였다. 콘크리트 바닥판 및 강재 하부플랜지는 각각 면의 차원을 가지는 기학학적 환형섹터로, 수평면내에서 폭이 좁게 투영되어 나타나는 상부플랜지 및 복부판은 선의 차원을 가지는 기하학적 호로 가정되었다. 제안된 반력산정식의 형식은 비교적 단순하고 그 예측값은 유한요소해석으로 얻은 값과 비교하였을 때 오차가 1% 수준으로 잘 일치하였다.

Horizontally curved bridges are subjected to torsional loads by their vertical dead loads only as well as eccentric loads, which cause negative reactions at supports. In this paper, effects of bridge curvature on vertical reactions at supports are investigated for 48.8 m length simple span steel box girder bridges with elastomeric bearings by varying curvature angle from 0.49 to 1.35 rad. In order to expect magnitude and direction of reactions including possibility of negative reactions, reaction evaluation equations have been analytically developed by separating a superstructure of curved bridge into independent components. Concrete slabs and bottom flanges in steel box section are assumed geometrical annular sectors in area dimension, and top flanges and webs that have very narrow projected areas are assumed geometrical arcs in line dimension. Proposed equations have relatively simple forms and prediction values are on very good agreement with those from finite element analyses by difference of 1% order.

철도 판형교의 선받침, 스페리칼받침 및 디스크받침의 차량주행에 의한 동적 거동을 측정 분석 하고, 각 받침에 따른 판형교의 동적 거동을 분석하였다. 이를 위해 각 받침은 고정단과 가동단의 형태에 따라 차량주행에 의한 수직변위가 측정되었고, 비교 분석하였다. 또한, 가동단의 스페리칼받침과 디스크받침의 내부에 설치된 PTFE판의 변형 및 이 변형이 교량의 거동에 미치는 영향을 분석하였다. 판형교에 설치된 교량받침에서 들림 현상이 관측되는데, 받침 형태에 따른 들림량을 분석하였다. 중앙 거더의 수직변위를 교량받침 별로 비교하여 교량받침 교체에 의한 교량 수직변위 변화를 분석하였으며, 각 받침에 따른 중앙 거더의 수직변위와 고유진동수의 변화를 상관적으로 분석하여 설명하였다.

Dynamic behaviors of line type bearings, spherical bearings and disk bearings which are being used for railway steel bridges are investigated, and that of the bridges is also analyzed. For the purpose, the vertical displacements of the three bearings including fixed and expansion type are measured and analyzed. Also, the deformation of the PTFE plate placed inside of spherical and disk bearings of expansion type is measured and its effect on the dynamic behavior of the bridges is discussed. The up-lift phenomenon at the bearings installed for the steel bridges is estimated. The vertical displacements at mid-span of the bridges are compared according to the bearing types. Finally, the 1st mode natural frequencies are estimated and the relationship to the vertical displacement is discussed.

The railway bridge of the domestic still has been used steel base such as sperical bearing and pot bearing widely. However, the bearing of steel series is occured corrosion frequently, reduced durability and raised maintenance cost excessively due to the nature of the material. If the elastomeric bearing which is widely used in highway bridge is applied to the railway bridge, it will be able to compensate this defect a lot. In order to apply to the railway bridge used for highway bridge, is needed the control of the bridge ends deflection, lateral displacement and negative reaction. Therefore, the elastomeric bearing can be applied to the railway bridge enough, if installed negative reaction key for control of the bridge ends deflection, improved shear wedge performance for control of the lateral force, adjust the thickness of the elastomeric pad for the minimize deflection, in addition, can be economic design of sub-structures due to damping effect.

The aim of the present study is the characteristics of bridge rubber pads and suggested how to determine the stiffness the pads. A disk bearing is operated as an elastic bearing in the vertical direction and is composed of a Polyether Urethane (polyurethane) disk for elastic support and Polytetrafluoroethylene (PTFE) to accommodate movement. Static tests are conducted in a laboratory to determine the static behavior of a Polyurethane disk. Finite Element (FE) analysis is also performed to verify the static performance. For dynamic behavior, four disk bearings having the identical Polyurethane disk used in the static tests are installed in a full size railway bridge and tested under a running locomotive. From the tests results, the static and dynamic stiffness of disk bearings are estimated and compared with each other. In the procedure to estimate the stiffness of a pad, the dead load(pre-load) of a bridge and live load of a vehicle are considered.

교량받침은 활하중, 크리프, 온도변화, 건조수축 등에 의한 상부구조의 변위를 흡수하는 역할을 수행한다. 국내 탄성받침 설계기준인 KS F 4420은 전단변형을 탄성받침 총 고무 높이의 70% 이내로 제한하고 있는데, KS F 4420에 의해 설계된 탄성받침이 요구되는 전단성능을 발휘하기 위해서는 허용 전단변형률이 전단파괴에 대하여 충분한 안전성을 보유해야 한다. 더욱이 탄성받침이 지진격리장치와 함께 내진설계에 사용될 수 있는 상황을 고려할 경우, 탄성받침은 KS F 4420의 허용전단변형률보다 높은 수준의 전단성능을 확보해야 한다. 이 논문에서는 국내 탄성받침의 전단성능을 확인하기 위하여 극한전단실험을 실시하였다. 실험 결과 탄성받침은 200% 이상의 전단변형률에서 파괴가 발생하여 KSF 4420의 허용전단변형률 규정이 안전 측이라는 사실을 알 수 있었다. 하지만 일체화된 거동을 할 것이라 기대 되었던 탄성받침이 200% 전단변형률 내외에서 받침 분리현상을 보였다. 관측된 받침분리 현상은 탄성받침의 내진설계 적용성을 고려할 경우 교량 시스템에 예기치 못한 충격 또는 집중 응력을 발생 시킬 수 있기 때문에 이러한 현상이 방지될 수 있도록 관련 규정이 필요하다고 판단된다.

The bridge bearings are devices absorbing the displacements of the superstructure. KS F 4420 relative to the design of elastomeric bearings in Korea allows shear deformation up to 70% of total rubber height. For the elastomeric bearings to fulfill their shear function required in the design, the stability of allowable shear strain of elastomeric bearings relative to the shear failure should be guaranteed. Moreover considering the possibility that elastomeric bearings are applied to the seismic design together with isolation devices, elastomeric bearings is supposed to display higher shear performance. In this paper ultimate shear performance tests were performed. The measured ultimate shear strains were over 200%. Therefore an allowable shear strain provision becomes safe. But elastomeric bearings expected to show their performance in one united body reveled the separation of components near 200% shear strain. These separation in elastomeric bearing can cause unexpected impact or concentrated stress to bridge system considering to application of seismic design. Therefore provision relevant to separation problem is necessary.

This paper reports a comparative study for performance evaluation guidelines for bridge bearings. Guidelines for bridge bearings such as KS, EN1337, AASHTO LRFD, and Japanese code were analyzed. In addition, fatigue tests of elastomeric bearing are being conducted for allowable shear deformation and compressive stress. Based on literature survey and tests, the innovative concept of performance evaluation guidelines for bridge bearings is suggested.