In this study, image quality and radiation dose changes will be examined to analyze the impact of tube voltage, tube current, and Pitch in Multi-dectector Computed Tomography(MDCT). This study aims to optimize Pitch changes to obtain diagnostically valuable images while minimizing patient radiation exposure, Using a MDCT system(Somatom Definition Flash, Siemens, Germany), parameters were varied as; tube voltage at 120 kVp and 140 kVp, tube current at 200 mAs, 250 mAs, and 300 mAs, and Pitch at 0.5, 0.8, 1.0, 1.2, and 1.5. AAPM phantom and the GAMMEX tissue-equivalent phantom model 467 was used. Signal-to-Noise Ratio(SNR), Contrast-to-Noise Ratio(CNR), Full Width at Half Maximum(FWHM) were measured using the ImageJ software(version 1. 8. 0). Based on 120 kVp, 200 mAs, 0.5 Pitch, comparative analysis of image quality was conducted for each variable. Results : Each phantom showed an overall decrease in SNR and CNR as the Pitch increased; however no significant differences were observed in FWHM. As in previous studies, increase in Pitch leads to an increase in effective thickness, thereby increasing the SSP in SDCT, while no significant difference was observed in MDCT. This study yielded similar results. However, there was a decrease in SNR and CNR with the increase of Pitch, therefore this study provides a valuable contribution by establishing a standard for image quality associated with Pitch changes, which was not previously presented.
한국어
MDCT에서 kVp, mA, Pitch 의 변화가 화질에 미치는 영향을 분석하기 위해 본 연구를 시작하였다. MDCT 시스템(독일 지멘스, Somatom Definition Flash)을 사용하여 매개변수를 다음과 같이 변경했다. 120 kVp 및 140 kVp의 튜브 전압, 200 mAs, 250 mAs 및 300 mAs의 튜브 전류, 그리고 0.5, 0.8, 1.0, 1.2 및 1.5의 피치를 사용했습니다. AAPM 팬텀과 GAMMEX 조직 등가 팬텀 모델 467이 사용되었다. 120 kVp, 200 mAs, 0.5 Pitch를 기준으로 각 변수에 대해 이미지 품질을 비교 분석했습니다. 각 팬텀은 피치가 증가함에 따라 SNR과 CNR이 전반적으 로 감소하는 것으로 나타났지만, FWHM에서는 유의미한 차이가 관찰되지 않았다. 선행연구에서 제시된 Pitch의 증가는 유효 두께의 증가로 이어져 SDCT에서 SSP가 증가하는 반면, MDCT에서는 유의미한 차이가 관찰되지 않았으므로, MDCT에서의 피치에 따른 반치폭 화질의 영향은 유의미한 차이가 없는 것으로 사료된다.
목차
Abstract Ⅰ. 서론 Ⅱ. 실험 재료 및 방법 1. 실험 기기 및 재료 2. 실험 조건 3. 실험 방법 4. SNR, CNR 획득 5. FWHM 측정 6. 통계분석 Ⅲ. 결과 1. SNR 2. CNR 3. FWHM Ⅳ. 고찰 및 결론 참고문헌 요약