Earticle

현재 위치 Home

Friction Stir Welding Tool Geometries Affecting Tensile Strength of AA6063-T1 Aluminum Alloy Butt Joint

첫 페이지 보기
  • 발행기관
    국제인공지능학회(구 한국인터넷방송통신학회) 바로가기
  • 간행물
    The International Journal of Advanced Smart Convergence KCI 등재후보 바로가기
  • 통권
    Volume 4 Number 1 (2015.05)바로가기
  • 페이지
    pp.145-153
  • 저자
    Kittipong Kimapong, Jesada Kaewwichit, Waraporn Roybang, Pramote Poonnayom, Sakchai Chantasri
  • 언어
    영어(ENG)
  • URL
    https://www.earticle.net/Article/A258683

※ 원문제공기관과의 협약기간이 종료되어 열람이 제한될 수 있습니다.

원문정보

초록

영어
Friction Stir Welding (FSW) is a solid state welding that could successfully weld the difficult-to-weld-materials such as an aluminum alloy. In this welding process, the stirrer of the welding tool is one of the important factors for producing the perfect sound joint that indicates the higher joint strength. So, this report aims to apply the friction stir welding using various stirrer geometries to weld the AA6063-T1 aluminum alloy butt joint, investigates the mechanical properties of the joint and then compares the mechanical properties with the microstructure of the joint. An experiment was started by applying the friction stir welding process to weld a 6.3 mm thickness of AA6063-T1 aluminum alloy butt joint. A study of the stirrer geometries effect such as a cylindrical geometry, a cone geometry, a left screw geometry and a right screw geometry at a rotational speed of 2000 rpm and a welding speed of 50-200 mm/min was performed. The mechanical properties such as a tensile strength and a hardness of the joint were also investigated and compared with the microstructure of the joint. The results are as follows. A variation of FSW Stirrer shape directly affected the quality AA6063-T1 aluminum alloy butt joint. A cylindrical stirrer shape and a cone stirrer shape produced the void defect at the bottom part of the weld metal and initiated the failure of the joint when the joint was subjected to the load during the tensile test. Left and right screw stirrer shapes gave the sound joint with no void defect in the weld metal and affected to increase the joint strength that was higher than that of the aluminum base metal.

목차

Abstract
 1. INTRODUCTION
 2. EXPERIMENTAL PROCEDURE
 3. RESULTS AND DISCUSSION
 4. CONCLUSION
 REFERENCES

키워드

friction stir welding aluminum tool shape tensile strength

저자

  • Kittipong Kimapong [ Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Pathumthani, THAILAND ] Corresponding Author
  • Jesada Kaewwichit [ Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Pathumthani, THAILAND ]
  • Waraporn Roybang [ Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Pathumthani, THAILAND ]
  • Pramote Poonnayom [ Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Pathumthani, THAILAND ]
  • Sakchai Chantasri [ Department of Industrial Engineering, Faculty of Engineering, Rajamangala University of Technology Thanyaburi, Pathumthani, THAILAND ]

참고문헌

자료제공 : 네이버학술정보

간행물 정보

발행기관

  • 발행기관명
    국제인공지능학회(구 한국인터넷방송통신학회) [The International Association for Artificial Intelligence]
  • 설립연도
    2000
  • 분야
    공학>전자/정보통신공학
  • 소개
    인터넷방송, 인터넷 TV , 방송 통신 네트워크 및 관련 분야에 대한 국내는 물론 국제적인 학술, 기술의 진흥발전에 공헌하고 지식 정보화 사회에 기여하고자 한다.

간행물

  • 간행물명
    The International Journal of Advanced Smart Convergence
  • 간기
    계간
  • pISSN
    2288-2847
  • eISSN
    2288-2855
  • 수록기간
    2012~2025
  • 십진분류
    KDC 326 DDC 380

이 권호 내 다른 논문 / The International Journal of Advanced Smart Convergence Volume 4 Number 1

    피인용수 : 0건 (자료제공 : 네이버학술정보)

    함께 이용한 논문 이 논문을 다운로드한 분들이 이용한 다른 논문입니다.

      출처 : 네이버학술정보

        0개의 논문이 장바구니에 담겼습니다.

        페이지 저장
        소속기관 조회
        이용자님의 소속기관(단체)이 서비스에 가입되어 있는지 확인해 보십시오.
        기관회원에 소속되어 있는 이용자는 원문을 무료로 이용할 수 있습니다.