K. Raghu Ram Mohan Reddy, M. M. M. Sarcar, N. Ramanaiah
언어
영어(ENG)
URL
https://www.earticle.net/Article/A206954
※ 원문제공기관과의 협약기간이 종료되어 열람이 제한될 수 있습니다.
원문정보
초록
영어
Ti6Al4V alloys are widely used in chemical plants, automobile, aerospace industries and medical applications (bone, dental) because of its high specific strength. But, it has poor wear resistance. In the present investigation, duplex coatings were employed to enhance the mechanical and tribological properties. WC-Co Ceramic coatings were deposited on Ti6Al4V substrate with different thicknesses (250μm, 350μm and 450μm) by the detonation spray (DS) while the thickness of the NiCrAlY bond coat (200μm) deposited by High Velocity Oxy Fuel (HVOF), stayed the same. Mechanical properties (hardness and wear resistance) were found for both substrate and duplex coatings. Wear test was performed for different sliding distances (1000m,2000m,3000m and 4000m) at a constant load of 50N by using a pin-on-disc apparatus, and the disc speed was recorded as 600rpm. XRD characterization was performed for substrates and coated samples. SEM analysis showed the wear behavior of coated and uncoated samples. Finally, it was concluded that 450μm ceramic top coat samples resulted maximum hardness and highest wear resistance.
목차
Abstract 1. Introduction 2. Experimental Work 2.1. Materials and Coating Deposition 2.2. Characterisation of Coatings 2.3. Surface Roughness Measurements 2.4. Microhardness 2.5. Wear Testing 3. Results and Discussion 3.1. Characterisation of Coatings 3.2. Surface Roughness Measurements 3.3. Microhardness Measurements 3.4.Wear Analysis 4. Conclusions Acknowledgements References
키워드
duplex coatingsceramic coatingsTi-6Al-4Vwear
저자
K. Raghu Ram Mohan Reddy [ Assistant Professor, Department of Mechanical Engineering, GITAM University, Visakhapatnam, INDIA ]
M. M. M. Sarcar [ Professor, Department of Mechanical Engineering, ANDHRA University Visakhapatnam, INDIA ]
N. Ramanaiah [ Associate Professor, Department of Mechanical Engineering, ANDHRA University Visakhapatnam, INDIA ]
보안공학연구지원센터(IJAST) [Science & Engineering Research Support Center, Republic of Korea(IJAST)]
설립연도
2006
분야
공학>컴퓨터학
소개
1. 보안공학에 대한 각종 조사 및 연구
2. 보안공학에 대한 응용기술 연구 및 발표
3. 보안공학에 관한 각종 학술 발표회 및 전시회 개최
4. 보안공학 기술의 상호 협조 및 정보교환
5. 보안공학에 관한 표준화 사업 및 규격의 제정
6. 보안공학에 관한 산학연 협동의 증진
7. 국제적 학술 교류 및 기술 협력
8. 보안공학에 관한 논문지 발간
9. 기타 본 회 목적 달성에 필요한 사업
간행물
간행물명
International Journal of Advanced Science and Technology
간기
월간
pISSN
2005-4238
수록기간
2008~2016
십진분류
KDC 505DDC 605
이 권호 내 다른 논문 / International Journal of Advanced Science and Technology Vol.57