현재 위치
Home
Optimization of Operating Parameters of Desiccant Wheel for Rotation Speed
-
- 발행기관
- 보안공학연구지원센터(IJAST) 바로가기
-
- 간행물
- International Journal of Advanced Science and Technology 바로가기
-
- 통권
- Vol.32 (2011.07)바로가기
-
- 페이지
- pp.109-116
-
- 저자
-
- 언어
- 영어(ENG)
-
- URL
- https://www.earticle.net/Article/A153521
※ 원문제공기관과의 협약기간이 종료되어 열람이 제한될 수 있습니다.
원문정보
초록
- 영어
- Desiccant wheels are used in commercial and industrial applications to perform air dehumidification operations by utilizing low grade heat source. Software provided by the manufacturer is used to select a honeycombed rotary desiccant wheel as per requirements of the client on the website by Novel Air Technologies. The performance of the software has been verified by comparing the results obtained by the software with those published in reputed journals. Using the software, the performance of an adiabatic rotary dehumidifier is parametrically studied and the optimal rotational speed is determined by examining the moisture removed by process area in the desiccant wheel. Also the effect of air flow rate on the reactivation air and process air has been studied. The basic parameters for a particular wheel of thickness 200 mm and diameter 550 mm are: ambient air at 30 0C DBT and 17 g/kg humidity ratio, process air flow rate vary between 1.5 m/s to 5.5 m/s, reactivation air flow rate lies between 1.5 m/sec to 5.5 m/sec and rotational speed of wheel varies from 10 RPH to 40 RPH. On the basis of results the following recommendations have been made: It was observed that for low velocity of process air (1.5 m/s to 2.5 m/s), 10RPH and 20RPH are found to be optimum for operation. In case of high velocity (>2.5), little effect of RPH is observed, however the most optimum RPH is found to be 20. For both high and low reactivation inlet velocity, 20 RPH is the most optimum rotation speed. However, the best results are observed at 3.5m/s to 4.5m/s reactivation inlet velocity.
목차
Abstract
1. Introduction
2. Desiccant Wheel
3. Case Study
4. Conclusion
References
저자
간행물 정보
발행기관
-
- 발행기관명
- 보안공학연구지원센터(IJAST) [Science & Engineering Research Support Center, Republic of Korea(IJAST)]
- 설립연도
- 2006
- 분야
- 공학>컴퓨터학
- 소개
- 1. 보안공학에 대한 각종 조사 및 연구 2. 보안공학에 대한 응용기술 연구 및 발표 3. 보안공학에 관한 각종 학술 발표회 및 전시회 개최 4. 보안공학 기술의 상호 협조 및 정보교환 5. 보안공학에 관한 표준화 사업 및 규격의 제정 6. 보안공학에 관한 산학연 협동의 증진 7. 국제적 학술 교류 및 기술 협력 8. 보안공학에 관한 논문지 발간 9. 기타 본 회 목적 달성에 필요한 사업
간행물
-
- 간행물명
- International Journal of Advanced Science and Technology
- 간기
- 월간
- pISSN
- 2005-4238
- 수록기간
- 2008~2016
- 십진분류
- KDC 505 DDC 605
이 권호 내 다른 논문 / International Journal of Advanced Science and Technology Vol.32
피인용수 : 0건 (자료제공 : 네이버학술정보)
함께 이용한 논문 이 논문을 다운로드한 분들이 이용한 다른 논문입니다.
출처 : 네이버학술정보
0개의 논문이 장바구니에 담겼습니다.